Makita DLS211 Manuel D'instructions page 30

Slide (push) cutting (cutting wide
workpieces)
WARNING:
Whenever performing a slide cut,
¿UVW SXOO WKH FDUULDJH IXOO WRZDUGV \RX DQG SUHVV
the handle all the way down, then push the car-
riage toward the guide fence. Never start the cut
with the carriage not pulled fully toward you. If
you perform the slide cut without the carriage pulled
fully toward you, unexpected kickback may occur and
VHULRXV SHUVRQDO LQMXU\ PD\ UHVXOW
WARNING:
Never attempt to perform a slide
cut by pulling the carriage towards you. Pulling
the carriage towards you while cutting may cause
unexpected kickback resulting in possible serious
SHUVRQDO LQMXU\
WARNING:
Never perform the slide cut with
the handle locked in the lowered position.
Fig.51: 1. Stopper pin
1. Unlock the stopper pin so that the carriage can
slide freely.
2. Secure the workpiece with the proper type of vise.
3. Pull the carriage toward you fully.
4. Switch on the tool without the saw blade making
any contact and wait until the saw blade attains full
speed.
5. Press the handle down and push the carriage
toward the guide fence and through the workpiece.
6. When the cut is completed, switch off the tool and
wait until the saw blade has come to a complete
stop before returning the blade to its fully elevated
position.
Miter cutting
5HIHU WR WKH VHFWLRQ IRU DGMXVWLQJ WKH PLWHU DQJOH
Bevel cut
WARNING:
After setting the blade for a bevel
cut, ensure that the carriage and saw blade will
have free travel throughout the entire range of the
intended cut before operating the tool. Interruption
of the carriage or blade travel during the cutting oper-
ation may result in kickback and serious personal
LQMXU\
WARNING:
While making a bevel cut, keep
hands out of the path of the saw blade. The angle
of the blade may confuse the operator as to the actual
blade path while cutting and contact with the blade
ZLOO UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
WARNING:
The saw blade should not be
raised until it has come to a complete stop. During
a bevel cut, the piece cut off may come to rest against
the saw blade. If the blade is raised while it is rotating,
WKH FXWRII SLHFH PD\ EH HMHFWHG E\ WKH EODGH FDXVLQJ
the material to fragment which may result in serious
SHUVRQDO LQMXU\
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
Fig.52
1. Remove the upper fence on the side that you are
going to tilt the carriage.
2. Unlock the stopper pin.
3. $GMXVW WKH EHYHO DQJOH DFFRUGLQJ WR WKH SURFHGXUH
H[SODLQHG LQ WKH VHFWLRQ IRU EHYHO DQJOH DGMXVWPHQW
Then tighten the knob.
4. Secure the workpiece with a vise.
5. Pull the carriage toward you fully.
6. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
7. Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade
and push the carriage toward the guide fence to cut
the workpiece.
8. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Left and Right 0° - 45°
When performing compound cutting, refer to the section
IRU SUHVV FXWWLQJ VOLGH SXVK FXWWLQJ PLWHU FXWWLQJ DQG
bevel cut.
Cutting base boards
CAUTION:
Make sure to use the horizontal
vise (optional accessory) when cutting the base
board.
CAUTION:
When cutting the workpiece of the
thickness 20 mm or thinner, make sure to use a
spacer block to secure the workpiece.
When cutting the base board in 45° miter angle, engage
the stopper lever to prevent the blade case from con-
tacting the base board. This will keep the clearance
between the base board and the blade case when the
carriage is fully pushed forward.
Refer to the SPECIFICATIONS for base board cutting
capacity.
Fig.53: 1. Stopper lever 2. Spacer block
3. Horizontal vise
30 ENGLISH
Bevel angle
Left and Right 0° - 45°