Makita 8414D Manuel D'instructions page 4

ENGLISH
1 Button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 Speed change lever
6 Action mode change lever
7 Arrow
8 Adjusting ring
SPECIFICATIONS
Model
Capacities
Concrete............................................... 13 mm
Steel ..................................................... 13 mm
Wood .................................................... 45 mm
Wood screw.......................................... 6 mm x 75 mm
Machine screw ..................................... 6 mm
-1
No load speed (min )
High (3)................................................. 0 – 1,600
Medium (2) ........................................... 0 – 550
Low (1) ................................................. 0 – 300
-1
Blows per minute (min
High (3)................................................. 0 – 24,000
Medium (2) ........................................... 0 – 8,250
Low (1) ................................................. 0 – 4,500
Overall length .......................................... 259 mm
Net weight ............................................... 2.4 kg
Rated voltage .......................................... D. C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for impact drilling in brick, concrete
and stone as well as for drilling without impact in wood,
metal, ceramic and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES FOR POWER
TOOL
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to hammer drill safety rules. If you use this power
tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Wear ear protectors with impact drills. Exposure
to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
4. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4
Explanation of general view
9 Graduations
10 Steel band
11 Grip base
12 Side grip
13 Protrusion
14 Groove
15 Sleeve
16 Bit
8414D
)
8434D
14 mm
13 mm
50 mm
6 mm x 75 mm
6 mm
0 – 1,700
0 – 600
0 – 300
0 – 25,500
0 – 9,000
0 – 4,500
259 mm
2.5 kg
D. C. 14.4 V
5. Hold the tool firmly with both hands.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
9. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS FOR
GEB003-1 CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
17 Bit holder
18 Depth rod
19 Clamp screw
20 Blow-out bulb
21 Limit mark
22 Brush holder cap
23 Screwdriver
8444D
16 mm
13 mm
65 mm
10 mm x 89 mm
6 mm
0 – 1,700
0 – 600
0 – 300
0 – 25,500
0 – 9,000
0 – 4,500
259 mm
2.7 kg
D. C. 18 V
ENC004-1