Drill Safety Warnings; Functional Description - Makita DA3010 Manuel D'instructions

ENGLISH
(Original instructions)
1 Lamp
2 Speed control screw
3 Switch lever
4 Higher
SPECIFICATIONS
Model
Capacities
Steel .................................................................. 10 mm
Wood ................................................................. 25 mm
–1
No load speed (min ) .................................... 0 — 2,400
Overall length ..................................................... 270 mm
Net weight .............................................................. 1.6 kg
Safety class ...........................................................
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
This tool is intended for drilling in wood, metal and plas-
tic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

DRILL SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Explanation of general view
5 Lower
6 Reversing switch lever
7 Chuck key
8 Sleeve
8.
DA3010/DA3010F
DA3011/DA3011F
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
/II
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
To start the tool, simply squeeze the switch lever. Tool
speed is increased by increasing pressure on the switch
lever. Release the switch lever to stop.
GEA010-1
A speed control screw is provided so that maximum tool
speed can be limited (variable).
Turn the speed control screw clockwise for higher speed,
and counterclockwise for lower speed.
Reversing switch action (Fig. 2)
CAUTION:
• Always check the rotational direction before operation.
• Use the reversing switch only after the tool comes to a
GEB001-6
This tool has a reversing switch to change the rotational
direction. Move the reversing switch lever to the
tion (A side) for clockwise (forward) rotation or the
osition (B side) for counterclockwise (reverse) rotation.
Lighting up the lamps (Fig. 1)
For Model DA3010F, DA3011F
CAUTION:
• Do not look in the light or see the source of light
To turn on the lamp, start the tool. Then, the lamp lights
up the top of the bit. To turn it off, stop the tool.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
9 Ring
10 Gripping part
11 Side grip (handle)
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
unplugged before adjusting or checking function on the
tool.
the switch lever actuates properly and returns to the
"OFF" position when released.
complete stop. It will damage the tool to change the
rotational direction before the tool stops.
directly.
careful not to scratch the lens of lamp, or it may lower
the illumination.
posi-
F
p-
R
3