Lubrication - DeWalt D25951 Traduction De La Notice D'instructions Originale

locating professional power tools, equipment, and machines
using the D WALT Tool Connect™ app. For proper installation of
e
the D WALT Tool Tag refer to the D
e
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING:
• Always observe the safety instructions and
applicable regulations.
• Be aware of the location of pipework and wiring.
• Apply a pressure of approx. 20–30 kg to the tool.
Excessive force does not speed up chiselling but
decreases tool performance and may shorten tool life.
Proper Hand Position (Fig. B)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the main handle
Switching On and Off (Fig. A)
Switching on: set the On/off switch
Switching off: set the On/off switch
Demolition, Chasing and Channelling (Fig. A)
1. Select the appropriate chisel and clean.
2. Insert the chisel and check whether it is properly locked.
3. Fit and adjust the side handle
firmly tightened.
4. Hold the tool with both the main handle
side handle 5 and switch on. The tool now runs in
continuous operation.
5. Always switch off the tool when work is finished and
before unplugging.
Various types of chisels are available as an option.
Only D WALT recommended accessories should be used with
e
this product.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
WALT Tool Tag manual.
e
5 ,
2 .
1 to position 1.
to position 0.
1
5 and make sure it is
and the
2
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
This machine is not user-serviceable. Take the tool to an
authorised D WALT repair agent after approximately 100 hours
e
of use. If problems occur before this time contact an authorised
D WALT repair agent.
e

Lubrication

Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Accessory Maintenance (Fig. F)
Accessory maintenance at the right time guarantees optimal
results in application and a long and efficient accessory life.
Grind the chisels on grinding discs. Refer to Figure F for the
appropriate angles of the following chisels:
11 Spade-shaped chisel
Cold chisel
12
13 Pointed chisel
14 U-shaped chisel
15 Hollow chisel
Mortar chisel
16
Toothed chisel
17

WARNING: These chisels can be reground only a
limited number of times. If in doubt, contact your dealer
for recommendations.

WARNING: Ensure that the cutting edge does not show
discolouration caused by too much pressure. This may
impair the hardness of the accessory.
EngLIsh
WALT recommended
e
21