Output Signal Adjustment - Sony HKDV-900 Mode D'emploi

Output Signal Adjustment

Output Signal Adjustment
To carry out an output signal adjustment with this unit,
first select the output signal to which the adjustment
applies, then make the adjustment with the control
knobs.
1
HKDV-900
1
Press one of the HD, D1, and D2 buttons in the
output selection section, turning it on.
The indicators in the level adjustment section light
according to the selected signal, and show the
items which can be adjusted.
It is not possible to press two or more buttons
simultaneously and turn them it.
2
Turn the knobs in the level adjustment section to
make the adjustment.
To set the center value ("unity level")
Press the UNITY button. The button and the "U"
indicator light.
Pressing the UNITY button once more turns it off, and
returns the settings to their previous values.
To disable a specific adjustment knob
To disable a specific adjustment knob so that the
corresponding setting cannot be accidentally changed,
hold down the CANCEL button and press the UNITY
button or PRESET button.
The indicator goes off, and the adjustment knob no
longer operates.
To enable the adjustment knob again, hold down the
CANCEL button and press the UNITY button or
PRESET button once more.
Master gain adjustments
The MASTER adjustment knob adjusts the overall
output level, based on the Y signal level. If the setting
of the P or P signal would be outside the setting
B R
range, the setting takes the limit value of the range.
8(GB)
Adjustment ranges of settings
When the HD button is lit
Adjustment knob Setting range
MASTER GAIN
Y LEVEL
P LEVEL
B
P LEVEL
R
SET UP
SYNC PHASE
FINE (SYNC PHASE) ±118 nsec (13.5 nsec step)
∗ Switched by the VIDEO gain switch.
2
When the D1 button is lit
Adjustment knob Setting range
MASTER GAIN
Y LEVEL
B–Y LEVEL
R–Y LEVEL
SYNC PHASE
FINE (SYNC PHASE) ±140 nsec (37 nsec step)
CROSS COLOR
∗ Switched by the VIDEO gain switch.
** When the HKPF-525 is installed, the local settings are
used.
When the D2 button is lit
Adjustment knob Setting range
VIDEO LEVEL
CHROMA GAIN
HUE
SETUP LEVEL
SYNC PHASE
FINE (SYNC PHASE) ±140 nsec (37 nsec step)
CROSS COLOR
∗ Switched by the VIDEO gain switch.
** When the HKPF-525 is installed, the local settings are
used.
Note
The SYNC PHASE/FINE adjustment is common to
D1 and D2 outputs.
UNITY (PRESET)
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–10 to +10 %
–1.4 to +1.4 H
UNITY (PRESET)
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–0.5 to +0.5 H
0 to 99 (16 step) 46 (local setting)∗∗
UNITY (PRESET)
–∞ to +3 dB (–3 to +3 dB)∗
–∞ to +3 dB (–3 to +3 dB)∗
–15 to +15°
–10 to +10 IRE
–0.5 to +0.5 H
0 to 99 (16 step) 46 (local setting)∗∗
0 dB
0 dB
0 dB
0 dB
0 %
0 H
0 H
0 dB
0 dB
0 dB
0 dB
0 H
0 H
0 dB
0 dB
0°
0 IRE
0 H
0 H