Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
E N G L I S H
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Depth of cut adjustment (fig. A)
• Loosen the star knob (3) and set the saw shoe (10)
to the required position.
• Tighten the star knob.
For optimal results, allow the saw blade
to protrude from the workpiece by about
5 - 8 mm.
Mounting and adjusting the parallel fence (fig. B)
The parallel fence is used for cutting parallel to the
edge of the workpiece.
Mounting
• Insert the parallel fence (6) in the saw shoe (10)
as shown.
• Tighten the star knob (14).
Adjusting
• Slacken the star knob (14) and set the parallel
fence (6) to the desired width.
• Tighten the star knob (14).
en - 5
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
Bevel adjustment (fig. C)
The bevel angle can be adjusted between 0° and 45°.
• Slacken the star knob (13).
• Set the bevel angle by tilting the saw shoe (10).
The angle can be read on the bevel scale (12).
• Tighten the star knob (13).
Removing and installing the saw blade (fig. D)
60
• Open the blade guard (7).
• Rotate the saw blade until a screwdriver can be
6
10
inserted into the hole in the blade. This will
15
prevent the blade from rotating while being
20
loosened.
25
• If no screwdriver is available, or if the saw blade
-
used does not have a hole, lock the blade by
-
-
pressing the teeth into a piece of wood.
6
6
• Loosen and remove the blade bolt (8) and the
6
6
outer arbour collar (15) by turning the blade bolt
15
counterclockwise using the wrench (18) supplied.
15
• Replace the saw blade. The teeth must point in
20
the direction of rotation, which is shown by the
-
arrow on the upper guard housing.
• Reinstall the outer arbour collar and firmly tighten
the blade bolt by turning clockwise.
Adjusting the riving knife (fig. E)
For the correct adjustment of the riving knife (9),
refer to the inset in figure E. Adjust the clearance of
the riving knife when the saw blade is changed or
whenever necessary.
• Loosen the Allen screw (19) and pull out the
riving knife to its maximum length.
• Adjust the clearance and tighten the Allen screw.
Mounting and adjusting the optional guide rail
(DE6287) (fig. F)
• Mount your saw onto the 1500 mm guide rail
using the screws supplied with the guide rail.
Instructions for use
• Always observe the safety instructions
• Ensure the material to be sawn is firmly
• Apply only a gentle pressure to the tool
• Avoid overloading.
and applicable regulations.
secured in place.
and do not exert side pressure on the
saw blade.
18
Publicité
Table des Matières
