Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
Camera head
Item no. 1590245 - Endoscope camera head with transmitter 28 mm
Item no. 1602401 - Self-levelling camera head with transmitter 30 mm
Intended use
The product serves as an inspection camera for the endoscope basic devices BS-1000T and
BS-1500T (not included in delivery, can be ordered separately). In addition to this, the product
is compatible with the endoscope finder BS-M 100 (not included in delivery, can be ordered
separately).
The product is suitable for optical troubleshooting or inspection of long pipe systems as well
as at powered-down systems and facilities. The flexible camera neck allows the camera on
top to access inaccessible positions. The 12 LEDs built into the camera head allow recording
in completely dark areas. The waterproof camera neck and camera head are designed for
contact with liquids (no acids or alkaline solutions). It is forbidden to use the product on people
and animals and in potentially explosive environments. Power is supplied via the connected
endoscope device.
For safety and approval purposes, you must not rebuild and/or modify this product. Using the
product for purposes other than those described above may damage the product. In addition,
improper use can cause hazards such as a short circuit, fire or electric shock. Read the
instructions carefully and store them in a safe place. Only make this product available to third
parties together with its operating instructions.
This product complies with statutory national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Delivery contents
• Camera head
• Hex key
• 2 x screws
• 3 x rubber ring
• Operating Instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
on this page. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle indicates that there is a risk to your
health, e.g. due to an electric shock.
The icon with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we will assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a
dangerous toy for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts,
flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorized use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Always handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
• Always observe the safety and operating instructions of any other devices which
are connected to the product.
• Make sure that the plug always remains dry and clean, especially if you screw it
on the connector.
• Only hold the camera head and camera neck in liquids that do not carry a live
voltage.
• The endoscope may only be used for inspecting facilities that are not connected
to a power source.
• The camera head is made from metal and can lead to short circuits when used
without the protective cap.
• For safety reasons, turn off all power sources before each inspection.
• Avoid heavy mechanical loads and vibrations.
• Always comply with accident prevention regulations for electrical equipment when
using the device in industrial facilities.
• Attention, LED light:
- Do not look directly at the LED light!
- Do not look into the beam directly or with optical instruments!
• Consult a technician if you are not sure how to use or connect the product.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Product overview
1 LEDs
2 Camera lens
3 Spiral spring
4 512 Hz transmitter
5 Rubber ring
a) Item no. 1590245
b) Item no. 1602401
6 Thread
7 Screw
8 Connector (not included)
9 Hex key
Publicité
Table des Matières
