Roland XY Série Mode D'emploi page 36

Instruc- Compati- Format
tion bility
SA SA;
SC SC Xmin,Xmax,Ymin
,Ymax(,type(,left,bottom));
SC Xmin,Xfactor,Ymin
,Yfactor,type;
SC;
SG SG g;
SG;
SI SI w.h;
SI;
SL SL tanø;
SL;
SM SM s;
SM;
SP SP n;
SP;
SR SR w,h;
SR;
SS SS;
TL TL lp(,lm);
TL;
UC UC (c,)É¢x1,É¢y1((,c),
É¢x2,É¢y2...,É¢xn,É¢yn); ∆xn: Number of
UC;
UF UF d1(,d2,.....d20);
UF;
VS VS v(,n);
VS;
WD WD c1c2.....cn
[label terminator]
WD [label terminator]
WG WG r,ø1,øc(,ød);
XT XT;
YT YT;
Parameter Range
None
Xmin,Ymin: User : *1
coordinate of P1
Xmax,Ymax: User : *1
coordinate of P1
type: Scaling type : 0,1,2
left : 0—100 (%)
bottom : 0—100 (%)
Xfactor: User X : *1
coordinate of P1
Yfactor: User Y : *1
coordinate of P2
g: Group number : 0—8 [0]
w: Character width : *1 (cm) [0.285cm]
h: Character height : *1 (cm) [0.375cm]
tanø: Character slant : *1 [0]
s: Character or symbol : CHR$ (33)—CHR$ (58)
,CHR$ (60)—CHR$ (126)
(If no parameter, symbol mode OFF)
n: Pen number : 0—8 [0]
w: Character width : *1 (%) [0.285cm]
h: Character height : *1 (%) [0.375cm]
none
lp: Tick length in : *1 (%) [0.5%]
positive direction
lm: Tick length in : *1 (%) [0.5%]
negative direction
c: Pen cotrol value : -8388608—-9999,+9999—+8388607
X-axis directional : -9998—+9998
moving units
∆yn: Number of
: -9998—+9998
Y-axis directional
moving units
d1—d20: : *2
Hatching spacing
partition ratio
v: Pen speed : 1-42 cm/sec
n: Pen number [Value by automatic pen sensing]
: 1-8 [All eight pens]
cn: Character
r: Radius : *1
ø1: Start angle : *3
øc: Center angle : *3
ød: Chord tolerance : *3 [5°]
None
None
([ ]: Default)
• The number of allotted units of each font is as follows:
Fixed character width font: 48(W) x 64(H)
Optimum character width font: 42(W) x 72(H)
• Normal characters are plotted within the following range. It
means that if you define a character so as to be accommodated in
there, it becomes the same size as a normal character.
Fixed character width font: 32(W) x 32(H)
Optimum character width font: 28(W) x 36(H)
The maximum number of parameter you can set is 20.
• The pen speed can be set in the unit of 1cm/sec.
• The parameter range of 1—8388607 is for no error.
• If the pen speed is set over 42, it will be set at 42.
• If the pen number is set over 9, the instruction is ignored.
• You can input a polygon of up to 250 vertices into the polygon
buffer in the state of being initialized. If you, however, input a
polygon of vertices more than the buffer capacity, an error occurs.
• The default tick length of X-axis is 0.5% of (P2y-P1y) in the
positive and negative directions, respectively.
• The default tick length of Y-axis is 0.5% of (P2x-P1x) in the
positive and negative directions, respectively.
Expanation
33