Roland XY Série Mode D'emploi page 33

Liste des instructions
en RD-GL II
* 1: - ( 2 23 )—( 2 23 -1)
23
* 2: - 0— + ( 2 -1)
* 3: - ( 23 )°—+ ( 2 23 -1)°
15 15
* 4: - ( 2 )— + ( 2 -1)
Instruc- Compati- Format
tion bility
AA AA x,y,øc(,ød);
AF AF;
AH AH;
AP AP n;
AP;
AR ∆x,∆y,øc(,ød);
AR
BL BL c1c2...cn
[label terminator]
BL [label terminator]
CA CA n;
CA;
CC CC øc;
CC;
CI CI r(,ød)
CM CM n1(,n2);
CP CP nx,ny ;
CP ;
CS CS n;
CS;
CT CT n;
CT;
DC DC;
DF DF;
DI DI run,rise;
DI;
DL DL n(,pc),x1,y1.....
(,pc).....,xn,yn;
DL n;
DL;
DP DP;
DR DR run,rise;
DR;
DS DS s,n;
DS;
30
Cette liste indique la compatibilité du langage RD-
GL II avec le DXY-1350A/1150A et les paramètres
pour chaque instruction.
Parameter Range
x,y: Center : *1
coordinate
øc: Center angle : *3
ød: Chord tolerance : *3 [5°]
None
None
n: Pen control value 0-225 (Decimal fractions are rounded.)
∆x,∆y: Relative
: *1
coordinates to the center
øc: Center angle : *3
ød: Chord tolerance : *3 [5°]
cn: Character
n: Character set : -1,0-59,70,80,99,101
number
øc: Center angle : *3 [5°]
r: Radius : *1
ød: Chord tolerance : *3 [5°]
n1: Character set 0-3
mode (Decimal fractions are rounded) [0]
n2: Fall back mode : 0 or 1
(Decimal fractions are rounded) [0]
nx: The number of X- : *1 (Decimal fractions are rounded)
axis directional characters
ny: The number of Y- : *1 (Decimal fractions are rounded)
axis directional characters
n: Character set : -1,0—59,70,80,99,101
number
n: Chord tolerance : 0 or 1
mode (Decimal fractions are rounded) [0]
None
None
run: X-axis : *1 [1]
directional vector
rise: Y-axis : *1 [0]
directional vector
n: Character number : 33—126 (Decimal fractions are rounded)
pc: Pen control : -128 (Decimal fractions are rounded)
xn,yn: Grid : -127—+127 (Decimal fractions are rounded)
coordinate values
none
run: X-axis : *1 [1]
directional vector
rise: Y-axis : *1 [0]
directional vector
s: Slot number : 0—1 (RD mode)
0—3 (ISO mode)
(Decimal fractions are rounded) [0]
n: Character set : -1,0—60,70,80,99
number (Decimal fractions are rounded)
: Compatible.
: Ignorée.
: Incompatible.
([ ]: Default)
The maximum character buffer capacity, including control
characters (e.g., label terminator) is 150 characters. Characters
more than 150 are ignored.
•Any character number without the range of *1 results in error
(3). If a character number is within that range, it results in error
(5) and the instruction is ignored.
The maximum center angle is 45°. This means that even if
specifying a center angle more than 45°, 45° will be set.
If any pen moving distance exceeds 8388607 and also any pen
movement to any coordinates exceeding *1, it results in error (3)
and the instructions are ignored.
Any character number without the range of *1 results in error (3).
If a character number is within that range, it results in error (5)
and the instruction is ignored.
Expanation