Roland XY Série Mode D'emploi page 34

Instruc- Compati- Format
tion bility
DT DT t;
DV DV n;
DV;
EA EA x,y;
EC EC n;
EC;
EP EP;
ER ∆x,∆y;
ER
ES ES w(,h);
EW EW r,ø1,øc(,ød);
FP FP;
FR FR;
FS FS f(,n);
FS;
FT FT n(,d(,ø));
FT;
GM GM pl(,dl(,r1(,r2(,r3))));
GM;
GP GP g(,h(,i(,j)));
GP;
IM IM e;
IM;
IN IN n;
IN;
IP IP P1x,P1y(,P2x,P2y);
IP;
IV IV s,(,t);
IV;
IW IW LLx,LLy,URx,URy;
IW;
KY KY k(,f);
KY;
LB LB c1c2.....cn
[label terminator]
Parameter Range
t: Label terminator [[ETX] (03h)]
n: Character : 0 or 1 [0]
direction (Decimal fractions are rounded)
x,y: : *1
Absolute coordinate
diagonal to rectangle
None
None
∆x,∆y:
: *1
Relative coordinate
diagonal to rectangle
w: Character spacing : *1 [0]
h: Line spacing : *1 [0]
r: Radius : *1
ø1: Start angle : *3
øc: Center angle : *3
ød: Chord tolerance : *3 [5°]
None
None
f: Pen force : 1-16
n: Pen number : 1-8 [All eight pens]
n: Pattern : 1—6 (Decimal fractions are rounded)
d: Spacing : *1 [ (P2x-P1x) x 0.01]
ø: Angle : *3 [0°]
pl: Polygon buffer The minimum, maximum and default values
dl: Downloadable of each buffer are shown in the table below.
character buffer
r1.r2,r3:
Ignored (Always 0)
g: Group number 1-8 (Decimal fractions are rounded.)
h: Pen number 1-8 (Decimal fractions are rounded.)
[Same as the group number]
i: Number of pens 1-8 (Decimal fractions are rounded.) [1]
j: Line length 1-5000(m) [100]
e: Error mask value : 0-255 (Decimal fractions are rounded) [223]
n: excluding some : -1
defaults
P1x,P1y: coordinate : *1
of P1
P2x,P2y: coordinate : *1
of P2
s: Slot number : 0—1 (RD mode)
(Decimal fractions are rounded)
0—3 (ISO mode)
(Decimal fractions are rounded)
[0]
t: Character table : 0 or 1 (Decimal fractions are rounded) [0]
LLx,LLy: coordinate : Maximum plotting area
at the lower-left corner [Maximum plotting area]
of a window
URx,URy: coordinate (Follows the panel key setting.)
at the lower-left corner
of a window
k: Key 1—4
f: Function 0—12
cn: Character
([ ]: Default)
If a value other than 0 or less than the min. value is specified, the
min. value will be set. If 0 is specified, 4 is set to the polygon
buffer, 0 to the downloadable character buffer, and 0 to the pen
sort buffer. If a value over the max. value is specified, the max.
value will be set. If an odd value is specified, an even value from
which 1 is subtracted will be set.
Even if the parameter exceeds the maximum plotting area when it
is within the *1 range, no error occurs.
Expanation
31