Teac TC-X350i Mode D'emploi page 9

After all connections are complete, connect the power
cord's plug to the AC wall socket.
< Read the instructions of each component you intend to use
with this unit.
< Be sure to connect each plug securely. To prevent hum and
noise, do not bundle the connection cords.
A
USB port
You can connect a USB memory device to this port.
B
AUX 2 IN
You can connect a portable audio player to this jack. Connect
the PHONES jack or audio output jack of a portable audio player
using commercially available stereo mini plug cable.
C
AUX 1/LINE OUT
Analog 2-channel audio signal is input or output from these
jacks. Connect a cassette tape deck etc. to these jacks using
commercially available RCA cables.
Make sure to connect:
e
White plug White jack (L: left channel)
e
Red plug Red jack (R: right channel)
D
VIDEO OUT
This terminal outputs video signal from an iPod connected to the
dock of the TC-X350i.
Connect the unit to the composite video connector of a
television or monitor using commercially available RCA (pin)
video cable.
Make the following settings on your iPod's menu to output video
to a TV via the dock.
In the [Video] menu, select [Video Settings],
and then set [TV OUT] to [On] or [Ask].
(iPod touch* does not have this menu.)
* iPod touch 1st generation: Software ver. 2.2 or later
< When you have set [TV OUT] to [Ask], each time you play a video
your iPod prompts you to specify whether to output it to a TV.
< When you output video to a TV from your iPod, the video is not
displayed on the iPod's screen.
E
iPod port
Insert the dock adapter that fits your iPod into the TC-X350i dock
(see page 15). Connect the dock to this port and then insert an
iPod into the dock.
F
AM loop antenna
Connect the supplied AM loop antenna to the AM antenna
terminal. Place the antenna in the direction which gives the best
reception.
To stand the loop antenna on a surface, fix the claw to the slot in
the antenna base.
Press the lever, insert the end of the cord to the terminal, then
release the lever.
< Make sure it is fastened securely by pulling the cord lightly.
< Make sure only the bare, stripped wire is inserted in the jack and
that no plastic insulation is preventing contact between the
antenna wire and terminal.
G
FM antenna
Connect the supplied lead-type FM antenna to the FM 75Ω
socket and extend the lead.
Adjust the antenna in a suitable location like a window frame or
wall which gives the best reception and then fix the antenna in
that position with thumb tacks or the like.
H
SPEAKERS
Connect the supplied speakers to the SPEAKERS terminals using
the supplied speaker cables.
Make sure to connect:
+ Red terminal + Red terminal of the speaker
e
(Using red marked side of the speaker cable)
_ Black terminal _ Black terminal of the speaker
e
How to connect
e Main unit's terminals
1 Turn the terminal cap counterclockwise to loosen it. The
speaker terminal caps cannot be fully removed from the base.
2 Insert the wire into the terminal fully and turn the terminal cap
clockwise to securely connect it.
e Speaker's terminals
Press the lever, insert the end of the cord to the terminal, then
release the lever.
< Make sure it is fastened securely by pulling the cord lightly.
< Make sure none of the wire insulation is under the terminal, only
the bare, stripped wire.
I
SUBWOOFER OUT
Connect a subwoofer using a commercially available RCA cable.
Use a subwoofer with built-in amplifier referred to as a "powered
subwoofer".
J
Power cord receptacle
After all other connections have been made, insert the supplied
AC power cord into this receptacle, then connect the other end
of the power cord into the wall socket.
Be sure to connect the power cord to an AC outlet which
supplies the correct voltage.
In order to avoid the risk of electric shock, fire, and so on, use
only the supplied power cord.
< If you are not going to use the unit for some time, disconnect the
power cord from the wall socket.
9