Typical Installation - Friedrich QuietMaster SS Instructions D'installation

FIGURE F
TRIM MOULDING
SCREW #12A X 2" LONG
USE 3.
SILL PLATE
GUIDE CHANNEL
INSIDE WALL
STEP 6 STEP 6 STEP 6
STEP 6 STEP 6
Slide the cabinet into the hole far enough to allow the guide-channel of the sill plate to contact the
inside wall surface (See Figure F).
STEP 7 STEP 7 STEP 7 STEP 7 STEP 7
Drill three (3) 5/23" dia. pilot holes through holes in sill-plate into framing and install three (3) #12A x 2"
long screws (See Figure F).
NOTE: ALTERNA NOTE: AL NOTE: AL NOTE: AL NOTE: AL TERNA TERNATE F TERNA TERNA TE F TE FASTENERS WHICH MA TE F TE F ASTENERS WHICH MA ASTENERS WHICH MA ASTENERS WHICH MAY BE USED FOR SECURING THE SILL PL ASTENERS WHICH MA
THE OUTSIDE W THE OUTSIDE WALL (NOT FURNISHED BUT A THE OUTSIDE W THE OUTSIDE W THE OUTSIDE W ALL (NOT FURNISHED BUT A ALL (NOT FURNISHED BUT A ALL (NOT FURNISHED BUT AV V V V V AIL ALL (NOT FURNISHED BUT A
MOLLY OR TOGGLE BOLT
STEP 8 STEP 8
STEP 8 STEP 8 STEP 8
Drill two (2) 5/32" dia. pilot holes each side at the locations shown (see Figure F, page 13) and install four
(4) #12A x 2" screws (Item # 4, page 2). Provided that Step 5 (hole construction) provides a sturdy mount
with solid vertical studs, no support brackets are required. The installation must support the weight of
the unit plus an additional weight of 400 pounds on the rear of the cabinet.
If support brackets are available, they can certainly be used for through-the-wall installations as shown
in Figure F, page 13.
If the reliability of the wall is in question, a window installation kit which includes support brackets can
be ordered (see Accessories).
STEP 9 STEP 9 STEP 9
STEP 9 STEP 9
If desired, trim around the cabinet on the room side with a suitable frame moulding furnished by the
installer (see Figure F).
STEP 10 STEP 10 STEP 10 STEP 10 STEP 10 Complete the installation by following steps 13 through 18 of SASH WINDOW INSTALLATION INSTRUCTIONS,
Pages 7 and 8.
STEP 11 STEP 11 STEP 11 STEP 11 STEP 11 Refer to the "OPERATING GUIDE" for instructions.

TYPICAL INSTALLATION

SURFACE
Y BE USED FOR SECURING THE SILL PLA A A A A TE IN THE W Y BE USED FOR SECURING THE SILL PL Y BE USED FOR SECURING THE SILL PL Y BE USED FOR SECURING THE SILL PL
AILABLE A AIL AIL AIL ABLE AT L ABLE A ABLE A ABLE A
CAULK ALL
SIDES
AIR TIGHT
NOTE: SUPPORT BRACKETS MAY BE OMITTED
FROM THROUGH-THE-WALL INSTALLATIONS IF
THE CABINET IS SECURED AS FOLLOWS.
DRILL 2 HOLES IN EACH SIDE AND INSTALL 4
FASTENERS (2 EACH SIDE). USE #12 X 2"
SCREWS, TOGGLE BOLTS OR EXPANSION
ANCHOR BOLTS AS SHOWN IN STEP 7.
SUPPORT BRACKETS AVAILABLE AS OPTIONAL ACCESSORY.
SCREW #12 X 2" LONG, USE ONE EACH
BRACKET. DRILL 5/23 DIA. PILOT HOLES.
T LOCAL HARDW T L T L T L OCAL HARDW OCAL HARDW OCAL HARDW OCAL HARDWARE STORE). ARE STORE). ARE STORE). ARE STORE). ARE STORE).
EXPANSION ANCHOR BOLT
3/8" SLOPE DOWN
TE IN THE W TE IN THE W TE IN THE WALL AND THE SUPPORT BRA TE IN THE W ALL AND THE SUPPORT BRA ALL AND THE SUPPORT BRA ALL AND THE SUPPORT BRACKETS TO ALL AND THE SUPPORT BRA CKETS TO CKETS TO CKETS TO CKETS TO
Page 13