Replacement Of Spool; Trouble Shooting; Maintenance And Care; Repair Service - FlexoTrim ART 1522 AA Manuel D'utilisation

Replacement of spool

First, switch off and unplug the device. Wait until the nylon thread
has come to a halt.
15
1
16

Trouble shooting

• Cutting line disappears into spool: Remove spool, pull end of line
through the metal outlet and reinsert spool. In case nylon line is used
up insert a new spool with line.
Do not make any other repairs on your own; have your trimmer
checked and repaired by an authorised dealer.

Maintenance and care

Clean your battery-operated mowing machine thoroughly each time after
you use it. Remove the grass and dirt. Clean the ventilation openings.
It is best to clean the plastic parts with a wet cloth and a soft detergent.
Never use aggressive detergents or solvents. Do not pour water into the
machine and do not sprinkle it with water. Store the mowing machine in
a dry place, never expose it to frost and keep it out of children's reach.
For more extensive maintenance or repairs, give the mowing machine
to the service center.

Repair service

Repairs to electric power tools should only be carried out by specialist
electrical personnnel.

Waste disposal and environmental protection

Dispose of the machine properly after it is worn out. Disconnect the
mains cable in order to prevent misuse. Do not dispose of the machine
with the household waste. In the interest of environmental protection,
take it to a collection point for electric machines. Your responsible local
authority can provide you with addresses and operating times. Also take
the packaging materials and worn out accessories to the appropriate
collection points.
Only for EU countries
Do not discard electric tools in the household waste!
In accordance with European Directive 2012/19/EC on waste electrical
and electronic equipment and its implementation in national law, waste
electric tools must be collected separately for environmentally-compati-
ble re-use.
GB | Operating Instructions
Then push the two locking de-
vices 1 at the sides of the cutting
head, and remove the cutting
head cover 2 (fig. 15).
1
Remove the used thread coil
and put in the new coil 3 such,
2
that the (one) end of the thread
comes out of the (each) outlet
at the side(s) of the cutting head
(fig. 16). Please take care that
3
the spring 4 is properly seated
under the thread coil. Finally,
4
close the cover by pushing it in
its seat. Both locks must properly
engage.
1
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is alternatively ob-
ligated to take part in the proper recycling in the case of relinquishment
of ownership. The waste equipment can also be taken to a collection
facility which disposes of it in the sense of the national recycling ma-
nagement and waste acts. This does not pertain to the accessory parts
and auxiliary equipment without electrical components accompanying
the waste equipment.

Spare parts

Please contact our service department if you need accessories or spare
parts.
When working with this machine, do not use spare parts other than those
recommended by us. Using spare parts not recommend by us can result
in serious injuries to persons or damage to the machine.
The following information should be provided when ordering spare parts:
• Type of machine
• Item number of the machine
Replacement spool AA
Protection cover
Accu 24V
Charger 24V

Warranty

For this electric tool, the company provides the end user - independently
from the retailer's obligations resulting from the purchasing contract -
with the following warranties:
The warranty period is 24 months beginning from the hand-over of the
device which has to be proved by the original purchasing document.
For commercial use and use for rent, the warranty period is reduced to
12 months. Wearing parts, batteries and defects caused by the use of
not fitting accessories, repair with parts that are no original parts of the
manufacturer, use of force, strokes and breaking as well as mischievous
overloading of the motor are excluded from this warranty. Warranty
replacement does only include defective parts, not complete devices.
Warranty repair shall exclusively be carried out by authorized service
partners or by the company's customer service. In the case of any inter-
vention of not authorized personnel, the warranty will be held void.
All postage or delivery costs as well as any other subsequent expenses
will be borne by the customer.

Technical Details

Cordless Grass Trimmer
Operational voltage
No-load Speed
Cutting Width
Line Diameter
Line Length
Battery type
Max. operational time
Weight
Sound Pressure Level
(according to 2000/14/EG)
Vibration
(according to EN 60335-2-91)
Mains battery charger
Mains voltage
Charging voltage
Charging current
Period of charging
We reserve the right to make changes to the technical specifications.
GB-6
Art.-No. 13001551
Art.-No. 17180065
Art.-No. 17180230
Art.-No. 17100760
ART 1522 AA
24 V DC
10.000 min
-1
22 cm
1,4 mm
1 x 6 m
Li-Ion 24V / 2,25 Ah / 54 Wh
approx. 35 - 40 Min
2,3 kg
75 dB(A)
K = 3,0 dB
< 2,5 m/s ²
2
K = 1,5 m/s
230 V~ / 50 Hz
25,2 V DC
500 mA
approx. 5 ½ hours