Safety Information
IC compliance Class B
CAN ICS-3(B)/NMB-3(B)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromet-
tre le fonctionnement.
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this
product.
Failure to follow all instructions listed below may result
in electric shock, fire, property damage and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the prod-
uct cease to be legible or become detached, replace with-
out delay.
• The product must only be installed, operated and ser-
viced by qualified personnel in an industrial environ-
ment.
Starting the tool
Fit the tool with a suitable socket.
Select the appropriate Pset.
Hold the tool by means of the handle and apply to the fas-
tener to be tightened.
8
WARNING Risk Of Injury
As the reaction force increases in proportion to the tight-
ening torque, there is a risk of severe bodily injury of the
operator as a result of unexpected behavior of the tool.
Press the trigger to start the tool.
Intended use
This product is intended to be used only by adults who have
read and understood the instructions and warnings in this
manual and can be considered responsible for their actions.
• This product is designed for installing and removing
threaded fasteners in wood, metal or plastic.
• Do not use the product for any other purpose not de-
scribed above.
Product Specific Instructions
Warning!
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow a fluid to flow
inside them. Corrosive or conductive fluids, such as sea-
water, certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
Battery
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the perfor-
mance of the battery pack. Avoid extended exposure to heat
or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used. To obtain the longest possible battery
life remove the battery pack from the charger once it is fully
charged.
The battery pack has overload protection that protects it from
being overloaded and helps to ensure long life. Under ex-
treme stress the battery electronics switch off the product au-
tomatically. To restart, switch the product off and then on
again. If the product does not start up again, the battery pack
may have discharged completely. In this case it must be
recharged in the battery charger.
Maintenance instructions
• Follow local country environmental regulations for
safe handling and disposal of all components.
• Maintenance and repair work must be carried out by
qualified personnel using only original spare parts. Con-
tact the manufacturer or your nearest authorised dealer
for advice on technical service or if you require spare
parts.
• Always ensure that the machine is disconnected from en-
ergy source to avoid accidental operation.
© Chicago Pneumatic - 8940176366
Cordless Impact Wrenches
Make sure that the tool is in perfect working order
►
and the system is programmed correctly.