Ego Power+ ST1510E Mode D'emploi page 10

◾
after striking a foreign object;
EN
◾
whenever the machine starts vibrating abnormally.
◾
Take care against injury to feet and hands from the
cutting means.
◾
Always ensure that the ventilation openings are kept
clear of debris.
MAINTENACE AND STORAGE
◾
Disconnect the machine from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾
Use only the manufacturer's recommended
replacement parts and accessories.
◾
Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾
When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾
Avoid Dangerous Environments – Don't use
appliances on damp or wet slope.
◾
Keep guards in place and in working order.
◾
Keep hands and feet away from the cutting area.
◾
To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾
Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾
For best results, your battery should be charged in a
location where the temperature is greater than 5° C
and less than 40° C. Do not store it outside or in vehicles.
◾
If you are approached, stop the motor and cutting
unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
10
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1510E
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade
A dull blade is more likely to snag and thrust
(only using with 3-teeth blade).
◾
A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾
Use only with battery packs and chargers listed in
fig.A.
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Voltage
No-load Speed
Cutting Mechanism
Cutting Line Type
Cutting Width
Recommended Operating Temperature 0°C-40°C
Recommended Storage Temperature -20°C-70°C
Weight
(without battery pack)
Measured sound power level L
WA
Sound pressure level at
operator's ear L
PA
Guaranteed sound power level L
(according to 2000/14/EC)
Front-assist Handle
Vibration a
h
Rear Handle
56 V
4000-5800 /min
Bump Head
2.4mm nylon
twist line
38 cm
3.2 kg
92.6 dB(A)
K=0.8 dB(A)
72.6 dB(A)
K=2.5 dB(A)
93 dB(A)
WA
3.5 m/s 2
K=1.5 m/s
2
2.1 m/s
2
K=1.5 m/s
2