Adding A New Security Detector To The Siren; Deleting All Devices From The Siren; Service Mode / Operating Mode - Honeywell FRIEDLAND FGGA04 Série Manuel D'installation Et D'utilisation

5.5

Adding a new security detector to the siren

In order to communicate with the siren, the ID code of the security detector must be learned by the siren. The siren can learn
up to 12 security detectors (door/window contact detectors or PIR movement detectors).
During setup, the siren will automatically power up in service mode, ready to learn a new security detector. If the siren is in
operating mode, refer to the section "Service mode / Operating mode" to switch to service mode.
1
Press and hold the
The siren emits one short beep. The indicators in the front lens and the learn indicator flash slowly. The siren
2
The siren emits two short beeps. The indicators in the front lens and the learn indicator flash quickly.
Note: If the confirmation signal is not received within 30 seconds, the siren will exit learn mode. The siren will remain in
Note: If the security detector has already been linked or if the maximum number of 12 security detectors are linked, the
siren will emit one short beep and exit learn mode. The indicators in the front lens and the learn indicator will go
3
Press the tamper switch on the security detector again within 15 seconds to confirm the ID code.
The siren emits three short beeps. The indicators in the front lens and the learn indicator come on for 3 seconds and
Note: If the confirmation signal is not received within 15 seconds, the siren will emit one short beep and exit learn mode.
5.6

Deleting all devices from the siren

1. Switch the siren into service mode using the remote control or the remote keypad.
2. Remove the siren from the wall.
3. Press and hold the learn button for 10 seconds until the siren emits two long beeps and the learn indicator flashes 5 times.
The ID codes of all linked devices are erased from memory. The siren remains in service mode.
5.7

Service mode / Operating mode

If you install the siren for the first time, it will automatically power up in service mode. Before testing or operating the siren, it
must be switched into operating mode.
If you use the siren with a control panel, refer to the Installation and Operation Manual for the alarm system.
If you use the siren without a control panel, use the remote control or the remote keypad:
1
Press and hold the
If you press the
disarm signal and the siren will emit two normal beeps. The system is disarmed.
If you press and hold the
will emit two short beeps followed by one long beep. The indicators in the front lens and the learn indicator will
flash together with the beeps. The system will return to service mode.
If you press the
disarm signal. The siren will not respond to the disarm signal, as it is still in service mode.
If you press and hold press the
siren will emit one long beep followed by two short beeps. The indicators in the front lens and the learn indicator
will flash together with the beeps. The siren will return to operating mode in a disarmed condition.
Remote control
button for 5 seconds.
remains in learn mode for 30 seconds.
Program the ID code:
Press the tamper switch on the security detector.
Confirm the ID code:
go off. The siren returns to service mode.
The indicators in the front lens and the learn indicator will go off.
Remote control
button for 5 seconds.
To switch from operating mode into service mode:
button (remote control) or the
button (remote control) or the
Switching from service mode into operating mode:
button (remote control) or the
button (remote control) or the
Enter the 4-digit ID code. Press and hold the
button for 5 seconds.
service mode.
off.
Enter the 4-digit ID code. Press and hold the
button for 5 seconds.
button (remote keypad), the device will transmit the
button (remote keypad) for 5 seconds, the siren
button (remote keypad), the device will transmit the
button (remote keypad) for 5 seconds, the
8
Remote keypad
Remote keypad