Care & Cleaning; Troubleshooting - Sage Nutri Juicer Plus Guide Rapide

Care & Cleaning
Ensure the juicer is turned off by pressing the
ON / OFF button on the control panel to OFF.
Then switch the appliance off at the power
outlet and unplug the cord. Ensure the juicer
is correctly disassembled.
FOR EASIER CLEANING
• Clean as you go and avoid dried on juice or
pulp residue.
• Immediately after each use, rinse removable
parts in hot water to remove wet pulp. Allow parts
to air dry.
• To minimise cleaning, line the pulp container with
a plastic freezer bag to collect the pulp. Pulp can
then be used in other dishes or as compost for
the garden or discarded.
CLEANING THE MOTOR BASE
1. Wipe the motor base with a soft, damp cloth
then dry thoroughly.
2. Wipe any excess food particles from the
power cord.
Do not use abrasive scouring pads or cleaners
when cleaning the parts or motor base as they may
scratch the surface.
CLEANING THE FILTER BOWL
SURROUND, JUICER COVER,
FROOJIE INSERT, FOOD PUSHER,
®
PULP CONTAINER
1. Wash all parts in warm soapy water with a soft
cloth. Rinse and dry thoroughly.
The filter bowl surround, juicer cover and pulp
container are dishwasher safe (top shelf only).
The Froojie Insert is not dishwasher safe. Please
®
wash in warm water.
CLEANING THE JUICE JUG
1. Rinse the juice jug and lid with froth attachment
under running water.
2. Wash both parts in warm soapy water with
a soft cloth. Rinse and dry thoroughly.
• The juice jug and lid are dishwasher safe
(top shelf only).
• Discolouration of the plastic may occur
with strongly coloured fruit and vegetables. To
help prevent this, wash parts immediately after
use. If discolouration does occur, the plastic parts
can be soaked in water with 10% lemon juice or
they can be cleaned with a non abrasive cleaner.
10
WARNING
Do not immerse the motor base in water or
any other liquid. The centre of the juice disc
and feed chute contains small sharp blades
to process fruit and vegetables during the
juicing function. Do not touch blades when
handling the juice disc or feed chute.
CLEANING THE JUICE DISC
For consistent juicing results always ensure that
the juice disc is thoroughly cleaned using the
supplied cleaning brush.
1. Soak the juice disc in hot soapy water for
approximately 10 minutes immediately after
juicing is completed. If pulp is left to dry on
the filter it may clog the fine pores of the filter
mesh thereby lessening the effectiveness of
the juicer.
2. Using the cleaning brush, hold the juice disc
under running water and brush from the inside
of the basket to the outer rim. Avoid touching
the small sharp blades in the centre of the juice
disc. After cleaning the juice disc, hold it up
towards a light to ensure the fine mesh holes
are not blocked. If the holes are blocked, soak
the juice disc in hot water with 10% lemon juice
to loosen the blocked holes. Alternatively, wash
the juice disc in the dishwasher.
• The juice disc is dishwasher safe
(top shelf only).
• Do not soak the juice disc in bleach or other
abrasive cleansers.
• Always treat the juice disc with care as it can be
easily damaged.

Troubleshooting

POSSIBLE PROBLEM EASY SOLUTION
Machine will not work when The safety locking arm may not be correctly engaged in the vertical
•
switched ON operating position with the locking arm located into the two grooves on
either side of the juicer cover.
Motor appears to stall when juicing • Wet pulp can build up under the juicer cover if the juicing action is too
vigorous. Try slower juicing action by pushing the food pusher down more
slowly. Follow cleaning instructions and clean the filter bowl surround, the
juice disc and the juicer cover.
• The juicer will automatically stop operating if the motor is stalled for more
than 10 seconds. Either too much food is being processed at one time
or the pieces are not small enough. Try trimming the food or cutting into
smaller pieces of even size and processing a smaller amount per batch.
To continue juicing, reset the juicer by pressing the ON / OFF switch on
the control panel to OFF then turn the appliance back on by pressing
ON / OFF switch to ON.
• Hard fruits and vegetables will put excess strain onto the motor if a low
speed is selected. Please refer to the juicing guide to determine the
correct speed for the fruits and vegetables selected for juicing.
Excess pulp building up the Stainless • Stop the juicing process, remove the juicer cover, scrape off pulp,
Steel Filter Disc reassemble and begin juicing again. Try alternating (soft and hard)
vegetable and fruit varieties.
Pulp too wet and reduced • Try a slower juicing action.
extracted juice
• Remove juice disc and thoroughly clean mesh walls with a cleaning
brush. Rinse the juice disc under hot water. If the fine mesh holes are
blocked, soak the basket in a solution of hot water with 10% lemon juice
to unblock the holes or wash in the dishwasher.
This will remove excess fibre build up (from fruit or vegetables) which
could be inhibiting the juice flow.
Juice leaks between the rim of the • Try a slower juicing speed and push the food pusher down the feed chute
juicer cover more slowly.
Juice sprays out from spout • Use juice jug and lid provided, or if juicing into a glass use the custom
designed juice nozzle.
• Try using fruits with more water content to help flush through the contents.
Additionally, try a slower juicing action by feeding one piece in at a time
and by pushing the food pusher down more slowly.
When using the Froojie extractor, the • Try using fruits with more water content to help flush through the contents.
®
filter bowl surround becomes full and Additionally, try a slower juicing action by feeding one piece in at a time
clogs its spout and by pushing the food pusher down more slowly.
Overheating with excessive loads. • The juicer is fitted with a safety device which safeguards against
overheating with excessive loads. If overheating occurs, the juicer will
automatically activate the overload protection device and the unit will
switch itself off. When the overload protection is activated, unplug the
juicer from the power outlet for at least 15 minutes to allow the unit to cool.
Then plug the juicer into the power outlet and use as normal.
EN
11