Care & Cleaning - Sage the Nutri Juicer Cold XL Guide Rapide

Care & Cleaning
Ensure the juicer is turned off by turning the
juicer dial to the OFF position. Then unplug
the power cord.
CLEANING
1. Remove Juice Jug.
2. Remove Pulp Container.
3. Disengage Locking Bar, pull up entire
Juice Collector Assembly and take to sink.
Rinse all parts after use (except the motor
base) under running water to clear away
the majority of juice and pulp. Wash in warm
soapy water with a soft cloth.
To avoid food drying on to the blades, mesh
or transparent parts, rinse and wash as soon
as possible after use.
PULP CONTAINER
To minimize cleaning, you can line the pulp
container with a biodegradable bag to collect
the pulp.
MOTOR BASE
To clean the motor base, wipe with a soft,
damp cloth then dry thoroughly. Wipe any
excess food particles from the power cord.
Do not immerse the motor base in liquids.
CLEANING AGENTS
Do not use abrasive scouring pads or
cleaners on either the motor base or the jug,
as they may scratch the surface. Use only
warm soapy water with a soft cloth.
DISHWASHER
Wash all parts (except the motor base) in
warm soapy water with a soft cloth. All parts
except for the motor base and food pusher
are dishwasher safe. However washing parts
on a regular base in the dishwasher can
shorten the life of them due to prolonged
exposure to harsh detergents, hot water
and pressure.
8
Cleaning the parts in the dishwasher also
may cause parts to deteriorate so inspect the
parts regularly and stop using the product if
any signs of damage is noticed.
FILTER BASKET
To ensure consistent juicing results, always
clean the filter basket thoroughly immediately
after use.
If pulp is left to dry, it may clog the fine pores
of the filter mesh, which can affect juicing
performance. The filter basket can be
soaked in hot soapy water for 10 minutes,
if necessary.
Hold the filter basket under running water and
use brush (supplied with the juicer)
in a circular motion to clear away pulp from
the inside of the basket, including the blades.
Turn over to brush away pulp from the outside
of the basket, and repeat if necessary.
After cleaning, hold up towards a light source
to check that the fine mesh pores are not
blocked. If blocked, soak the filter basket in
hot water with 10% lemon juice to loosen,
and brush under running water again. Do not
soak the filter basket in bleach, harsh
chemicals or abrasive cleansers.
Always treat the filter basket with care, as it
can be easily damaged. Do not use if there is
any damage or deformation to the filter mesh.
The centre of the filter basket has an array
of small, sharp blades. Do not touch these
blades when handling the filter basket.
STUBBORN FOOD STAINS
Discolouration of the plastic may occur
with strongly coloured fruit and vegetables.
To help prevent this, wash parts immediately
after use.
If discolouration does occur, the plastic
parts can be soaked in water with
10% lemon juice or can be cleaned
with a non-abrasive cleaner.
Troubleshooting
Juicer will not work • The safety locking arm may not be correctly engaged in the vertical
when switched ON operating position. Check the top cover is properly aligned and the locking
arm is located firmly into the two grooves on either side of the juicer cover.
• Motor overload protection may have operated (see below).
Overheating with • The juicer is equipped with an internal self-resetting overload to prevent the
excessive loads motor from damage under heavy or continuous loads. If the motor suddenly
stops working, turn the dial to OFF, and unplug the unit from the power
outlet. Allow the juicer to cool for at least 30 minutes before operating again.
NOTE: The unit MUST be turned off in order for it to cool and be reset.
• Despite this overload protector, we suggest juicing in smaller batches,
without excessive pushing force, to avoid overheating and stalling and to
maintain the life of the motor.
Excess pulp building
• Stop juicing, disassemble to scoop excess pulp off the juicer cover.
up in the stainless Reassemble and continue juicing. Alternating soft and hard ingredients may
steel filter basket help avoid this.
Pulp too wet • The cleaner the filter, the better the juice yield, and dryer the pulp. Be sure to
and reduced thoroughly clean the juicer as soon as possible after each use. Remove the
extracted juice stainless steel filter basket and thoroughly clean mesh walls with a cleaning
brush. Rinse the filter basket under hot water. If the fine mesh holes are
blocked, soak the basket in a solution of hot water with 10% lemon juice to
unblock the holes or wash in the dishwasher (top shelf). This will remove
excess fiber build up which could be inhibiting the flow.
Juice leaks between • Try a slower juicing speed and push the food pusher down the feed chute
the rim of the juicer more slowly.
and the juicer cover
• Also ensure there is no build up in the filter basket.
Juice sprays out • The juice is being extracted too fast; try a slower juicing speed (if possible)
from spout and push the food pusher down the feed chute more slowly.
EN
9