Nice Industrial D-PRO ACTION NDCC2000 Manuel D'utilisation page 3

GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian)
CAUTION Important safety instructions. Follow all instructions as improper installation may cause serious damage
CAUTION Important safety instructions. It is important for you to comply with these instructions for your own and other
people's safety. Keep these instructions
• Before commencing the installation, check the "Product technical specifications", in particular whether this product is suitable for automating
your guided part. If it is not suitable, DO NOT continue with the installation.
• The product cannot be used before it has been commissioned as specified in the chapter on "Testing and commissioning"
CAUTION According to the most recent European legislation, the implementation of an automation system must comply
with the harmonised standards provided by the Machinery Directive in force, which enables declaration of
the presumed conformity of the automation. Taking this into account, all operations regarding connection to
the electricity mains supply, as well as product testing, commissioning and maintenance, must be performed
exclusively by a qualified and skilled technician!
• Before proceeding with the installation of the product, check that all materials are in good working order and suited to the intended applications
• The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by anyone with
insufficient experience or familiarity.
• Children must not play with the appliance
• Do not allow children to play with the control devices of the product. Keep the remote controls out of reach of children.
CAUTION In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be powered
through an external switching device, such as a timer, or connected to a supply that is regularly powered or switched off by
the circuit
• Provide a disconnection device (not supplied) in the plant's mains power supply, with a contact opening distance that permits complete
disconnection under the conditions dictated by overvoltage category III
• Handle the product with care during installation, taking care to avoid crushing, denting or dropping it, or allowing contact with liquids of any
kind. Keep the product away from sources of heat and naked flames. Failure to observe the above can damage the product, and increase the
risk of danger or malfunction. If this should happen, stop installation immediately and contact Customer Service.
• The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.
In such cases the warranty for material defects is excluded
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be carried out by unsupervised children
• Before working on the system (maintenance, cleaning), always disconnect the product from the mains power supply
• Check the system periodically, in particular all cables, springs and supports to detect possible imbalances, signs of wear or damage. Do not use
if repairs or adjustments are necessary, because a failure with the installation or an incorrectly balanced automated system may lead to injury
• The packing materials of the product must be disposed of in compliance with local regulations
Special warnings in relation to European directives applicable to the product
• "Construction Products" Regulation: Special warnings for this product in relation to Regulation 305/2011:
- The full installation of this product, as described in this instruction manual and for certain types of use (e.g. excluding use solely for vehicles)
may cause the product to fall within the scope of Regulation No. 305/2011 and its harmonised standard EN 13241-1.
- It is necessary to apply all the installation criteria to ensure that the product meets the essential requirements of Regulation No. 305/2011;
the installer must check and make sure that all these criteria have been scrupulously complied with.
- The essential requirements might not be guaranteed if the product is installed and used without compliance with one or more of these
criteria. It is forbidden to use the product in such circumstances until the installer has verified compliance with the Directive requirements;
in this case the "ES13241-1.4870" label attached to the product must be removed immediately and the "EC Declaration of Conformity"
(Annex I to this manual) cannot be used. As a result, the installer in turn becomes the manufacturer of the product and must comply with
the provisions of Regulation No. 305/2011 and its harmonised standard EN 13241-1. In this case the product must be considered as
"partly-completed machinery" and the "Declaration of Conformity" of Annex II can be used (for inclusion in the technical documentation).
• "Low Voltage" Directive:
Special warnings regarding the fitness of use of this product in relation to the "Low Voltage" Directive. This product meets the requirements
in the "Low Voltage" Directive, if used for the use and in the configurations specified in this instruction manual and in combination with the
items in the Nice S.p.a. product catalogue.
If the product is used in unspecified configurations or with other unspecified products, the requirements may not be guaranteed; the use
of the product in such circumstances is prohibited until the installer has verified compliance with the specified requirements of the directive.
• "Electromagnetic compatibility" Directive:
Special warnings regarding the fitness of use of this product in relation to the "Electromagnetic compatibility" Directive.
This product has been subjected to electromagnetic compatibility tests in the most critical situations of use and in the configurations specified
in this instruction manual and in combination with the items in the Nice S.p.a. product catalogue.
If the product is used in unspecified configurations or with other unspecified products, the electromagnetic compatibility may not be guar-
anteed; the use of the product is prohibited in such circumstances until the installer has verified compliance with the specified requirements
of the directive.
Installation criteria and special warnings in connection with essential requirements
• When installed correctly, this product meets the essential requirements laid down in Regulation No. 305/2011 according to the requirements
in harmonised standard EN 13241-1, as indicated in Table 1 and in the European directive on "Machinery" 2006/42/EC.
• Release of dangerous substances:
The product does not contain and/or release hazardous substances in accordance with the requirements of EN 13241-1, 4.2.9 and accord-
ing to the list of substances on the website of the European Community
Special warning to ensure the continued compliance with the requirement – It is essential that the other materials used in the installation,
such as electrical cables, comply with this requirement.
• Safe opening for vertically moving doors: the product does not cause uncontrolled movements.
Special warnings to ensure continued compliance of the requirements:
- Install the product carefully following all the instructions described in Chapter "2 - Installation" and Chapter "4 - Testing and commissioning".
- Ensure that a maintenance schedule is organised which scrupulously complies with all the provisions in the Chapter "Maintenance
Schedule".
English – 3