WAGNER PROSPRAY 3.25 Mode D'emploi page 46

starting OperatiOn
TImeRS ScReeN
The Timers screen shows the total
time the sprayer has been turned on
as well as the total time the sprayer
has been running (pumping).
To select the Timers screen, press
the #4 key.
JoB TImeRS ScReeN
The Job Timers screen allows the
user to reset the "ON TIME" and "RUN
TIME" to track time on specific jobs.
To select the Job Timers screen,
press the #4 key. "JOB ON" screen
will appear. Press #3 to reset. Press
#1 to continue to "JOB RUN" screen.
Press #3 to reset. Press #1 to scroll through the remaining
menu screens.
SeRVIce TIme ScReeN
The Service Time screen allows the
user to set a service time interval
(in hours). Below the set time, the
screens shows the current amount of hours on the sprayer since
the last activation of the service timer. To select the Service
Timer screen, press the #4 key.
To set the service time, press the #2
(up) and/or the #3 (down) keys to the
desired time (run hours will increase/
decrease in increments of 25 for each time you press a key).
When the sprayer reaches the SERVICE@ time selected, the
screen will display "SERVICE DUE". To reset the timer, press
the #3 key when the pump is first turned on. This will reset the
"SERVICE DUE" message and also reset the "SERVICE TIME" to
the previous setting.
SecuRITy code ScReeN
The Security Code screen allows the
user to set a four digit security code
to prevent unauthorized use of the
sprayer. If a security code has been set, the control system
display will ask for the code at startup. If the correct code is
entered, the display will show the Main Screen and the sprayer
will operate. If the wrong code is entered, the display will
continue to ask for the correct code and the sprayer will not
work. To set or change the security code, press the #2 key.
46
TIMERS
MENU-1 SELECT-4
ON TIME XXXX
RUN TIME XXXX
JOB TIMERS
MENU-1 SELECT-4
JOB ON X
MENU-1 RESET-3
JOB RUN X
MENU-1 RESET-3
SERVICE TIME
MENU-1 SELECT-4
SERVICE @ XX
RUN HOURS XX
SECURITY CODE
MENU-1 CHANGE-2
If the sprayer is new, no security code is set and
i
the Main Screen will appear at startup. When
setting a security code for the first time, the
"Enter Old Code Number" screen will appear, and
you will need to enter "1111".
Enter the old security code number to access the screen that
allows the code change. If the wrong code is entered, the
display will continue to ask for the correct code and the security
code cannot be changed.
Enter the new security code. Once
the new code is entered, the display
will automatically ask that the new
code be re-entered for verification.
If the same new code is re-entered,
the display will confirm that the new
code has been accepted and return to the Main Screen. If the
new code is re-entered incorrectly, the display will return to the
"Enter New Code Number" screen and the process will repeat.
If you forget or misplace your security code, you can contact
Wagner customer service for assistance.
To inactivate the security function, enter "1111" at
i
the "Enter New Code Number" screen (this is the
default code that leaves the sprayer unlocked).
As a result, the Main Screen will appear at sprayer
startup.
PRIme ScReeN
The Prime screen appears when the
pressure control knob is set at the
"MIN" setting.
RAPId cLeAN ScReeN
The Rapid Clean screen appears
when the pressure control knob is
set at the RAPID CLEAN position and
the PRIME/SPRAY valve is in the PRIME position.
If there is no action at any menu screen for 30
i
seconds, the display will go back to the Main
Screen.
ps 3.25
ENTER NEW CODE
NUMBER XXXX
RE-ENTER NEW
NUMBER XXXX
NEW CODE NUMBER
ACCEPTED
PRIME
RAPID CLEAN