Publicité
Les langues disponibles
Les langues disponibles
or another device that controls
heater connection automatically.
2. Put the appliance plug into a socket.
Power selection knob
This unit is double insulated and no
Stop
carth connection is required.
3. Turn the thermostat knob in a
Low Power Heating, quiet mode- 1.000 W
clokwise direction, to the maximum
Low Power Heating- 1.000 W
position.
4. Select the Hetaing Power required:
High Power Heating - 2.000 W
Low Power 1.000 W, quiet mode;
Low Power 1.000W; High Power
Thermostat knob (B, fig. 1)
2.000 W.
5. Once the desired temperature in
Maximum position of the thermostat
the room has been archieved, turn the
Minimum position of the thermostat
thermostat knob in an anticlockwise
direction until a soft click is heard
The thermostat controls the heater to
and the unit switches off. From then
maintain the temperature selected bet-
on the heater will automatically select
ween minimum and maximum . When
the temperature.
selected room temperature is obtained
6. Disconnection, turn the power knob
the thermostat will switch heater off,
to the off position
and on, to maintain this setting.
Maintenance
Operation
1. Important, disconnect the unit from
1. Please ensure that the supply
the mains supply before carrying out
voltage is in accordance with the
any maintenance operation.
product rating plate (230 V 50 Hz).
2. Ever y season, clean the
2. Put the appliance plug into a socket.
2. Put the appliance plug into a socket.
accumulated dust from inside the unit
This unit is double insulated and no
This unit is double insulated and no
with a high pressure air jet or vacuum
carth connection is required.
carth connection is required.
cleaner. It is recommended that this
3. Turn the thermostat knob in a
3. Turn the thermostat knob in a
operation is carried out by a qualified
clokwise direction, to the maximum
clokwise direction, to the maximum
technician.
position.
position.
3. Clean the inlet and outlet grilles
4. Select the Hetaing Power required:
4. Select the Hetaing Power required:
regularly.
Low Power 1.000 W, quiet mode;
Low Power 1.000 W, quiet mode;
4. The appliance should not be dipped
Low Power 1.000W; High Power
Low Power 1.000W; High Power
in water for any reason nor should it
2.000 W.
2.000 W.
be put under a tap.
5. Once the desired temperature in
5. Once the desired temperature in
5. Do not dismantle the appliance in
the room has been archieved, turn the
the room has been archieved, turn the
any way as this will nullify the S&P
thermostat knob in an anticlockwise
thermostat knob in an anticlockwise
guarantee.
direction until a soft click is heard
direction until a soft click is heard
and the unit switches off. From then
6. If the supply cord of this appliance
and the unit switches off. From then
on the heater will automatically select
is damaged, it must only be replaced
on the heater will automatically select
the temperature.
by repair shop appointed by the
the temperature.
6. Disconnection, turn the power knob
6. Disconnection, turn the power knob
to the off position
on the heater will automatically select
the temperature.
6. Disconnection, turn the power knob
manufacturer because special
(A, Fig. 1)
to the off position
purpose tools are required.
Remark: it is very important that
Maintenance
regular maintenance of the fan
heater is carried out in order to reduce
1. Important, disconnect the unit from
the risk of possible fire hazards.
the mains supply before carrying out
any maintenance operation.
Overheating, switch off
2. Ever y season, clean the
accumulated dust from inside the unit
In the event of overheating due to
with a high pressure air jet or vacuum
any abnormal operation or failure, the
cleaner. It is recommended that this
safety protection device will
operation is carried out by a qualified
automatically switch the unit off. In
technician.
this event:
3. Clean the inlet and outlet grilles
1. Disconnect the appliance from the
regularly.
mains supply.
4. The appliance should not be dipped
2. Allow the unit to cool down for at
in water for any reason nor should it
least 15 minutes.
be put under a tap.
3. Make sure that the outlet grille is
5. Do not dismantle the appliance in
not obstructed by dust and if
any way as this will nullify the S&P
necessary it can be cleaned with a
guarantee.
vacuum cleaner.
6. If the supply cord of this appliance
If after these actions the appliance
is damaged, it must only be replaced
still does not work properly, we
by repair shop appointed by the
recommend that it be taken to your
manufacturer because special
S&P dealer.
manufacturer because special
purpose tools are required.
purpose tools are required.
Removal from service,
Remark: it is very important that
disposal and recycling
Remark: it is very important that
regular maintenance of the fan
regular maintenance of the fan
- EU regulations and our commitment
heater is carried out in order to reduce
heater is carried out in order to reduce
to future generations oblige us to
the risk of possible fire hazards.
the risk of possible fire hazards.
recycle used materials; please re-
Overheating, switch off
member to dispose of all unwanted
Overheating, switch off
packaging materials at the appropriate
recycling points, and to drop off ob-
In the event of overheating due to
In the event of overheating due to
solete equipment at the nearest waste
any abnormal operation or failure, the
any abnormal operation or failure, the
management point.
safety protection device will
safety protection device will
automatically switch the unit off. In
automatically switch the unit off. In
this event:
this event:
1. Disconnect the appliance from the
1. Disconnect the appliance from the
mains supply.
mains supply.
2. Allow the unit to cool down for at
2. Allow the unit to cool down for at
least 15 minutes.
least 15 minutes.
8
3. Make sure that the outlet grille is
230 V ~ 50 Hz 2.000 W
m
2
l
3
n
n
v
I
s
r
S
R
d
-
t
r
m
p
r
s
m
Publicité
