Publicité
Les langues disponibles
Les langues disponibles
with recharging the battery. (See related chapter).
5.
Pull the drive lever (4, Fig. C) with care until the
machine starts to move.
The speed is proportional to the pressure applied
to the drive lever (4, Fig. C).
Stopping the machine
To stop the machine, release the drive lever (4, Fig. C)
completely and pull back on handle bar.
To stop the brooms from rotating, turn the key (2, Fig.
B) to "0" position.
To lift the side broom (10, Fig. C), lift the knob (12, Fig.
C) (without turning it) and align the latch with the slot in
the plastic chassis. Rotate the knob (12) forward to
engage the latch (2).
MACHINE OPERATION
1.
Avoid stopping for a long time with the machine in
the same position and the brooms still rotating:
this could create unwanted marks on the floor.
2.
To pick-up large debris, lift the front flap by pulling
the lever (21, Fig. C); keep in mind that during this
operation the dust control of the machine will
decrease.
3.
For proper machine operation, the dust filter must
be as clean as possible. To clean the filter while
sweeping proceeds as follows according to the
type of filter-shaker installed:
a)
Manual filter - shaker: turn the ignition key in
the "0" position, then pull the handle (20, Fig.
C) outward until the end of the stroke is
reached and then release it: the return spring
strikes the dust filter frame and shakes it.
Repeat this operation several times. Turn the
ignition key in the "I" position to continue
working.
b)
Electric filter-shaker (optional) press and
hold the filter-shaker button (8, Fig. B) for a
few seconds.
NOTE:
Repeat the operation at least every ten
minutes while working (according to the
dust conditions)
.
NOTE:
During this operation the electric motors
and
all
automatically stopped.
146 0791 000(2)2004-02
machine
functions
NOTE:
When the hopper and/or filter are full the
machine can not collect more dust and
debris.
CAUTION!
To avoid damaging the dust filter do not
sweep wet floors or ground.
The hopper (17, Fig. C) should be emptied after each
working period and whenever it is full.
EMPTYING THE HOPPER
1.
Release the drive lever to stop the machine.
2.
Turn the ignition key (2, Fig. B) to the "0" position.
3.
Disengage the hopper latch (18, Fig. C) by pulling
the bottom outward.
4.
Using the hopper handle (19, Fig. C) remove the
hopper (17, Fig. C) from the machine and empty it.
5.
Return the hopper to its normal operating position
and engage the hopper latch (18, Fig. C).
6.
The machine is ready to start sweeping again.
AFTER MACHINE USE
When finished working:
1.
Clean the filter using the manual filter shaker (20,
Fig. C) or the electric filter-shaker, if equipped, by
pressing the filter shaker button (8, Fig. B).
2.
Empty the hopper (17, Fig. C) (see previous
paragraph).
3.
Lift the side broom by lifting the knob (12, Fig. C).
4.
Remove the ignition key (2, Fig. B) from the
machine.
5.
Ensure
that
independently.
6.
Activate the optional brake pedal (26, Fig. C).
PUSHING THE MACHINE
The machine can be moved my pushing it both with the
ignition key (2, Fig. B) in the "0" and in the "I" positions.
MACHINE STORAGE
If you foresee that the machine will not be used for
are
more than 30 days, proceed as follows:
– Move the machine to a suitable indoor storage area.
– Disconnect the battery connector (3, Fig. U).
– Lift the machine so that the skirts, the main broom
and the wheels do not touch the ground.
– Disconnect the positive battery terminal (+) from the
positive battery (+) pole.
OPERATOR MANUAL
the
machine
cannot
move
7
Publicité
Chapitres
Dépannage
