Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - Ergo tools Pattfield E-HKS 1600-Laser Mode D'emploi

Anleitung_E_HKS_1600_Laser_SPK7:_
To switch off:
Release the safety lock-off and button
If you release the handle the equipment will shut
down automatically which means that it cannot
operate accidentally.
Ensure that you do not cover or block the
ventilation openings whilst working with the tool.
Do not slow down the saw blade after you switch it
off by pressing it sideways.
Important! Do not put down the machine until the
saw blade has reached a complete standstill.
Important! Carry out a trial cut in a piece of
waste wood
6.4 Changing the saw blade (Fig. 6)
Important! Always pull out the power plug
before doing any work on the circular saw!
Only use saw blades of the same type as the saw
blade supplied with this circular saw. Ask your dealer
for advice.
Push back and secure the moving swing guard
hood (19) using the lever for the swing guard hood
(20).
Press the spindle lock (11).
Undo the screw to secure the saw blade (17)
using the Allen key (a).
Remove the flange (18) and the saw blade (12) in
a downwards direction.
Clean the flange and insert the new saw blade.
Pay attention to the running direction (see arrow
on the guard hood and saw blade).
Tighten the screw to secure the saw blade (17),
check it runs true.
Before you press the On/Off switch, make sure
that the saw blade is correctly fitted and that
moving parts run smoothly and the clamping
screws are tightened securely.
6.5. Using the laser (Figure 7-9)
The laser (15) enables you to make precision cuts
with your circular saw.
The laser light is generated by a laser diode
powered by two batteries. The laser light is
enlarged to form a line and is emitted through the
laser emission aperture. You can then use the line
as an optical marker for the sawing line for
precision cuts. Follow the laser safety instructions.
Inserting the batteries: Switch off the laser.
Remove the battery compartment cover (14).
Insert the batteries (ensuring that you fit them the
30.06.2009 13:01 Uhr
right way round). Fit the battery compartment
cover (14) again.
Switching on the laser:
Press the ON/OFF switch for the laser (13)
A red laser beam will now be projected from the
laser emission aperture. If you guide the laser
beam along the sawing line mark as you saw, you
will produce clean, precise cuts.
Switching off the laser:
Press the ON/OFF switch for the laser (13) again.
The laser beam will go out. Always switch off the
laser when not in use.
The laser beam can be blocked by deposits of
dust and chips. You should therefore remove
these particles from the laser emission aperture
before you use the laser.
Notes on batteries: If you do not intend to use the
laser for a lengthy period of time, remove the
batteries from the battery compartment. Any
leakage of battery fluid might damage the tool.
Do not place the batteries on heaters or expose
them to direct sunshine for long periods;
Temperatures in excess of 50°C may damage the
tool.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
Seite 15
GB
15