Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ATTACHING EXTENSION CORD TO MOWER (FIGURE 5)
DO NOT connect the extension cord to power source until you have
finished reading this manual and you are ready to start mowing.
1. The extension cord must be polarized and will only plug in one
way, orient the wide slot with the wide blade in the switch housing.
2. Loop the extension cord and push the loop up through the hole in the
switch housing.
3. Pull the extension cord on the side of the loop that is plugged into
the switch housing and remove all the slack in this section of the
extension cord.
4. Place the loop over the strain relief tab on the switch housing and
pull the extension cord so the loop draws down around the strain
relief tab as shown in the detail. Double check to see that you did
not loosen the extension cord.
5
SWITCH USE (FIGURE 6)
Your mower is equipped with a special switch. To operate the switch,
insert your finger into the opening (Figure 6) and push the lever out so
that you can grasp it with your other hand. Pull the lever back to turn
the unit on and hold it against the mower handle to keep it running. To
turn the mower off, just release the lever. The spring loaded "SNAP
ACTION" lever will quickly turn the mower off.
WARNING: NEVER ATTEMPT TO OVERRIDE THE OPERATION
OF THIS SWITCH.
6
EXTENSION CORD TO ELECTRICAL OUTLET (FIGURE 7)
1. Place most of the extension cord close to the electrical outlet, out
of the path of the mower. Attach extension cord to mower.
2. Start in direction where extension cord side of mower is closest to
the outlet. Begin mowing in the area closest to the outlet and mow
in a back and forth manner. Note the cord is kept on cut portion of
lawn and out of the path of the mower. (FIGURE 7)
3. Avoid mowing in circles as cord will be harder to manage.
7
FLIP-OVER HANDLE FEATURE (FIGURE 8)
1. By pulling the handle release lever and flipping the handle to the
opposite side of the mower, the cord remains on the same side of
the mower and out of the way.
2. You must mow in a back and forth pattern to benefit from this feature.
8
RECOMMENDED APPROXIMATE CUTTING HEIGHT
The cutting height should be higher in hot weather or shade , and
lower for the last mow before winter.
COOL SEASON GRASSES
TYPE
CREEPING BENT GRASS
VELVER BENT GRASS
ANNUAL BLUEGRASS
CANADA BLUEGRASS
KENTUCKY BLUEGRASS
ROUGH BLUEGRASS
SMOOTH BROMEGRASS
FINE RESUE
TALL FESCUE
ANNUAL RYEGRASS
WARM SEASON GRASSES
TYPE
BAHIA GRASS
BERMUDA GRASS
BUFFALO GRASS
CARPET GRASS
CENTIPEDE GRASS
ST. AUGUSTINE GRASS
ZOYSIA GRASS
NOTE: The cutting height range for your mower is 1" - 3-1/2"
25.4mm - 88.9mm
WHEEL HEIGHT ADJUSTMENT (FIGURE 9)
1. BEFORE MAKING ANY ADJUSTMENTS, TURN OFF, WAIT FOR
BLADE TO STOP AND UNPLUG MOWER.
2. Your mower features the Black & Decker single lever wheel height
adjust system. This system will adjust all four wheels at the same
time. Mower adjusts from 1 to 3 1/2" (25.4mm - 88.9mm) with six
increments.
3. Place your left hand on the height adjust handle and your right
hand on the lower handle as shown in Figure 9.
4. Pull height adjust handle away from mower, and re-set in the
desired height adjust position. (See recommended cutting height by
grass type under OPERATING INSTRUCTIONS) Rotating the
height adjust towards the front of the mower lowers the cutting
height, and rotating towards the rear raises the cutting height.
9
LOW
MULCHING TIPS
In the mulching configuration your new mower is designed to re-cut
the grass clippings into short lengths.
These clippings, which are dispersed as you mow will biodegrade
quickly and provide nutrients for the lawn.
5
SHADE
SUN
1-1/3" 33.7mm 2/3" 16.7mm
1/4"
6.3mm
1/2" 12.7mm
1/2"
12.7mm
1"
3"
76.2mm 4"
2-1/2" 63.5mm 3"
1"
25.4mm 1-1/2" 38.1mm
3"
76.2mm
4"
1-1/2" 38.1mm 2-1/2" 63.5mm
2-1/2" 63.5mm 4"
2"
50.8mm 2-1/2" 63.5mm
SHADE
SUN
2"
50.8mm
3"
1/2"
12.7mm
1"
1-1/2" 38.1mm 2-1/2" 63.5mm
1"
25.4mm
2"
1"
25.4mm 2"
2"
50.8mm 3"
1/2"
12.7mm 1"
CUTTING HEIGHT POSITIONS
Position
Cut
1 (LOW)
1" (25.4mm)
2
1-1/2" (38.1mm)
3
2" (50.8mm)
4
2-1/2" (63.5mm)
5
3" (76.2mm)
6 (HIGH)
3-1/2" (88.9mm)
HIGH
25.4mm
101.6mm
76.2mm
101.6mm
101.6mm
76.2mm
25.4mm
50.8mm
50.8mm
76.2mm
25.4mm
Publicité
Table des Matières
