Preparation; Precautions For Cordless Grass Trimmer - HIKOKI CG 36DA Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 36
English
c) Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
● Preparation
a) Before use check the supply and extension cord for
signs of damage or aging. If the cord becomes damaged
during use, disconnect the cord from the supply
immediately.
DO
NOT
TOUCH
DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or worn.
b) Before use, always visually inspect the machine for
damaged, missing or misplaced guards or shields.
c) Never operate the machine while people, especially
children, or pets are nearby.
d) Never replace nylon head with metalic cutting means.
● Operation
a) Wear eye protection, stout shoes and long trousers at all
times while operating the machine.
b) Avoid using the machine in bad weather conditions
especially when there is a risk of lightning.
c) Use the machine only in daylight or good artifi cial light.
d) Never operate the machine with damaged guards or
shields or without guards or shields in place.
e) Switch on the motor only when the hands and feet are
away from the cutting means.
f) Always disconnect the machine from the power supply
(i.e. remove the plug from the mains or remove the
disabling device)
whenever the machine is left unattended;
before clearing a blockage;
before checking, cleaning or working on the machine;
after striking a foreign object;
whenever the machine starts vibrating abnormally.
g) Take care against injury to feet and hands from the
cutting means.
h) Always ensure that the ventilation openings are kept
clear of debris.
i)
Never modify the unit/machine in any way. Do not use
your unit/machine for any job except that for which it is
intended.
● Maintenance, transport and storage
a) Disconnect the machine from the power supply (i.e.
remove the plug from the mains or remove the disabling
device) before carrying out maintenance or cleaning
work.
b) Use
only
the
replacement parts and accessories.
c) Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
d) When not in use, store the machine out of the reach of
children.
e) When transporting in a vehicle or storage, cover blade
with blade cover.
PRECAUTIONS FOR CORDLESS
GRASS TRIMMER
WARNING
1. Exercise patience in all work with the tool. And dress
properly to keep warm.
2. Plan all work ahead to prevent accidents.
3. Do not operate the tool at night or under bad weather
conditions when visibility is poor. And do not operate the
tool when it is raining or right after it has been raining.
Working on slippery ground could lead to an accident if
you lose your balance.
4. Inspect the nylon head before starting work.
Do not use the tool if the nylon head is cracked, scarred
or bent.
Make sure the nylon head is properly attached. A nylon
THE
CORD
BEFORE
manufacturer's
recommended
head that falls apart or comes loose during operation
could cause an accident.
5. Be sure to attach the cover before starting work.
Operating the tool without this parts could lead to injury.
6. Be sure to attach the loop handle before starting work.
Make sure it is not loose but properly attached before
starting work. Hold the loop handle fi rmly during work
and do not swing the tool around, but use the correct
posture and maintain your balance.
Losing your balance during work could lead to an injury.
7. Take care when starting the motor.
Place the tool on level ground.
Do not operate the tool within 15 m of people or animals.
Make sure that the nylon head does not come into
contact with the ground or trees and plants.
A careless start could lead to injury.
8. Do not secure the lock lever.
Accidentally pulling back the lever could lead to
unexpected injury.
9. Before leaving the tool, press the power button to turn it
off .
10. Operate the tool with care near electric cables, gas pipes
and similar installations.
11. Look out for and remove empty cans, wire, stones or
other obstacles before starting work. And do not work
near tree roots or rocks.
Working in such areas could damage the nylon head or
lead to injury.
12. Never touch the nylon head during operation.
Also make sure it does not come into contact with your
hair, clothes, etc.
13. In the following situations, turn off the motor and check
that the nylon head has stopped rotating.
To move to another work area.
To remove rubbish or grass that has become stuck in the
tool.
To remove from the work area obstacles or the rubbish,
grass and chips generated by trimming.
To lay down the tool.
Doing this with the nylon head still rotating could lead to
unexpected accidents.
14. Do not use the tool within 15 m of another person.
When you work with someone else, maintain a distance
of more than 15 m.
Flying chips could lead to unexpected accidents.
When working on unstable surfaces like slopes, make
sure that your co-worker is not exposed to any hazards.
Use whistles or other means for calling the attention of
your co-workers.
15. When grass and other objects become entangled in the
nylon head, turn off the motor and make sure the nylon
head has stopped rotating before removing them.
Removing objects from the nylon head when it is still
rotating will lead to injury.
Continuing operation when foreign matter is stuck in the
nylon head may lead to damage.
16. If the tool is operating poorly and produces strange noise
or vibrations, turn off the motor immediately and ask your
dealer to have it inspected and repaired.
Continued use under these conditions could lead to
injury or tool damage.
17. If you drop or bump the tool, inspect it carefully to check
there is no damage, cracks or deformation.
Using a tool that is damaged, cracked or deformed could
result in injury.
18. Secure the tool during vehicle transport to ensure that it
lies still.
Failure to heed this warning may result in an accident.
19. This product contains a strong permanent magnet in the
motor.
Observe the following precautions regarding adhering of
chips to the tool and the eff ect of the permanent magnet
on electronic devices.
8

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Cg 36dalCg 36dtaCg 36dtal

Table des Matières