Technical Specifications - SuperFish FallClear 10000 Notice D'utilisation

FallClear 10000
Biological filter with integrated UVC unit (Ultra Violet Clarifier). Suitable for ponds up to 10,000 litres.
The water enters the filter through the inlet. It then flows past the 11 Watt UVC unit, thus reducing algae growth while at the same time destroying harmful bacteria.
After the UVC unit, the Matala progressive filter mats are placed one behind the other in the filter, from coarse to fine. In this way, fish waste and floating debris are easily and
effectively trapped and filtered out of the water.
The last compartment holds the cassette with the substrate mix. This mixed substrate guarantees a high level of biological activity in the filter, while at the same time absorbing
harmful substances and reducing offensive odours.
The water then flows back into the pond via the outlet. By means of the sludge discharge (silt trap under the inlet) the trapped waste and debris can easily be drained off. (Cross-
section, drawing A.)
Maintenance
Always switch off the power supply before carrying out any maintenance or repair work on the unit!
- If your pond water is heavily polluted, the filter mats will need to be cleaned every day during the initial filtering phase. Subsequently they should be rinsed out with tap
water at least once a month (depending on the degree of pollution). The substrate mix should be cleaned twice a year in a bucket of pond water (do not use tap water!).
- Open the sludge discharge regularly to prevent waste and debris accumulating in the bottom of the filter.
- The UVC unit should be cleaned twice a year. If algae growth increases, the quartz glass tube around the PL-lamp should be cleaned. This tube can be simply removed using
a coin. Remove any calcium deposits with a suitable cleaning agent. Take care not to scratch the tube. The PL-lamp should be replaced after 8000 hours' use (approx. 1 year).
Do not touch the bulb with your bare hands.
Installation
Select the place where you want to fit the filter. The filter must be installed close to the pond and in an easily accessible position for maintenance. The inlet of the filter must be
above the water level of the pond so that the filter cannot overflow.
1. (Photo B) Fit an adaptor (a) with a nut (b) on the outlet. The nut (b) must be on the inside of the filter. A washer (c) must be fitted both on the inside and the outside of the filter. Make
sure that the washer (c) abuts properly and is not jammed in the screw thread.
2. (Photo A) Screw the sliding valve (e) on to the sludge discharge.
3. Remove the substrate (supplied with the module) from the plastic bag and place it (in the black substrate bag) in the substrate cassette (f).
4. Fit the UVC housing (g) with the quartz glass (h) on the inlet (i) on the inside of the filter. Cut off the transparent hose connector (j) to the required diameter. Screw the transparent hose
connector (j) together with a washer (k) on to the outside and tighten by hand. The hose from the pump must be attached to this hose connector (j).
5. Place the cover on the filter.
6. (Photo C) Fit the lamp (l) in the lamp holder (m) and position the integrated electrical section (n) on top of the UVC housing. Make sure that the washers (o) are correctly positioned. Then
tighten the electrical section with the nut (p). Make sure that the cover (n) is screwed straight into the UVC housing without crossed threads.
7. Start the pump and filter and check the system for leakage.

Technical specifications

UVC (W):
UVC PL-S Lamp:
UVC after 5,000 hours:
Pond water volume:
Recommended pump capacity per module:
Inlet adaptor:
Outlet bore:
Sludge discharge:
Choosing the right pump.
It is important to remember that a pump's rate of flow diminishes in direct proportion to the height difference that the water has to overcome. The first step when choosing
a pump is therefore to consider the difference in height between the water surface of your pond and the place where the filter is located. In case of doubt, consult your pond
specialist.
Tip
If your pond pump has a greater capacity than needed, use a two-way valve (Photo D).
3.4
11 Watt
85%
approx. 10,000 L (stocked with Koi fish: approx. 5,000L pond water volume)
max. 3500 l/h
1½" (40x32x25 mm)
50 mm
sliding valve (40 mm)
GB