Fender 65 TWIN REVERB Mode D'emploi page 7

A
A . POWER CORD - Connect the power cord to a grounded AC
receptacle in accordance with the voltage and frequency
ratings shown on the rear panel of your amplifier.
B . FUSE - Protects the amplifier from electrical faults. Replace
a blown fuse only with same type and rating as listed on
the fuse holder. If the amplifier repeatedly blows fuses,
take the amplifier to an authorized Fender Service Center.
C . POWER - Switches the amp ON and OFF and completely
disconnects the apparatus from the mains.
D . STANDBY - Use STANDBY instead of switching POWER off
for short breaks to eliminate the tube warm-up delay upon
returning to play. This will also extend tube life span.
CHASSIS
BOTTOM
FIG. 1
VIEW
A
B
TYPE:
PART NUMBER:
POWER REQUIREMENTS:
POWER OUTPUT:
IMPEDANCES:
SPEAKER COMPLEMENT:
TUBE COMPLEMENT:
DIMENSIONS:
WEIGHT:
`65 Twin Reverb – Rear Panel
B
Tube Adjustments
If the sound quality of the amp has degraded noticeably the tubes may be worn and need replacement. Output tube typically need
replacement before pre-amp tubes. If you are not sure about the condition of your tubes or the following procedures, take your amplifier to
an authorized Fender Service Center.
tube label, inside the cabinet.
A. HUM BALANCE ADJUSTMENT - This adjustment minimizes the hum heard at the speakers due to tube filament imbalance.
•Adjustment Instructions: Turn the amplifier ON for 2 minutes with nothing plugged into any of the INPUTS. Rotate the VIBRATO
CHANNEL volume, middle, and bass knobs fully clockwise and the treble knob fully counter-clockwise. Rotate ALL of the
NORMAL CHANNEL knobs fully counter-clockwise. Switch OFF the REVERB and VIBRATO effects. Insert a slotted screwdriver into the
BALANCE ADJUSTMENT control, (see "A" in FIG. 1) and rotate back and forth to the position with the least amount of hum.
B. BIAS ADJUSTMENT - This adjustment should be made only by an authorized Fender Service Center. BIAS needs adjustment only
if the replacement output tubes are not identical to the original tubes.
Specifications
PR 186
021-7300-000 (120V, 60Hz) USA,
021-7370-000 (100V, 50/60Hz) Japan,
360 watts
85 watts R.M.S.
INPUTS 1: 1M ohm (both channels), INPUTS 2: 136k ohms (both channels)
OUTPUT: 4 ohms (both speaker jacks together)
Two 12 in, 8 ohm Jensen ® (P/N-057146)
OUTPUT: Four Fender Special Design 6L6GC's (P/N-039214),
PRE-AMP: Four Fender Special Design 12AX7A's (P/N-013341),
Two Fender Special Design 12AT7's (P/N-023531)
HEIGHT: 19-7/8 in
WIDTH: 26-5/32 in
DEPTH:
10-3/8 in
Product specifications are subject to change without notice.
E
C D
E . MAIN SPEAKER - Plug-in connection for speakers. A
4-ohm minimum speaker must always be connected at this
jack when the amplifier is ON to prevent damage to the
amplifier.
F . EXTERNAL SPEAKER - Plug-in connection for an external
speaker. This jack is wired in parallel with the MAIN
SPEAKER JACK {E}. A total speaker impedance load of
4-ohms should be used to avoid
amplifier.
G . FOOTSWITCH - Plug-in connection for the FOOTSWITCH
which enables ON/OFF switching of the VIBRATO and
REVERB effects. The footswitch must be connected
and switched on for the Vibrato effect to function.
Replace tubes with identical Fender® original equipment only (see SPECIFICATIONS below). Tube location is printed on the
021-7360-000 (230V, 50Hz) Euro,
, 021-7330-000 (240V, 50Hz) Australia.
64 lb
7
F
damage to the
021-7340-000 (230V, 50Hz) UK
(49.2 cm)
(63.5 cm)
(21.9 cm)
(29 kg)
G