StreamLight TLR-3 Instructions D'utilisation page 4

6. Locate the "insert" side of the e-clip tool
and place it against the clamp surface.
7. Align the e-clip tool with the e-clip and
push the tool until the e-clip snaps
into place.
RAIL KEY REMOVAL
1. Fully tighten the rail clamp tension bolt.
2. The e-clip will become accessible on the end of rail clamp tension bolt.
3. Locate the "removal" side of the e-clip tool and place it against the clamp surface.
4. Place the tool on the e-clip and apply pressure to free the e-clip from the rail clamp tension bolt.
5. Unscrew the rail clamp tension bolt and remove it completely (the tension
spring must stay with the rail clamp tension bolt).
NOTE: A KEY MUST BE USED OR THE TLR-3 WILL SLIDE OFF THE FRONT OF THE RAIL UNDER RECOIL.
KEyS
KEY "A": SPRINGFIELD XD (COMPACT ONLY)
KEY "B": BERETTA 90two, BERETTA VERTEC
KEY "C": GLOCK, SPRINGFIELD XD (FULL FRAME), SMITH & WESSON TSW
KEY "D": KEL-TEC PF-9 (ONLY)
KEY "E": KIMBER TLE/RL II, SPRINGFIELD 1911, SIG GSR, BERETTA TICK ADAPTER,
SMITH & WESSON M&P, PICATINNY RAIL
MOUNTING/REMOvAL PROcEDURE
MAKE SURE THAT THE FIREARM IS UNLOADED AND THE BREECH IS OPEN. IT IS IMPERATIVE THAT
SAFETY MEASURES BE EMPLOYED AT ALL TIMES WHILE HANDLING THE FIREARM.
1. The TLR-3 is designed to be quickly attached
or detached from the side of the weapon or
accessory rail.
2. Loosen the rail clamp tension bolt.
3. Angle the TLR-3, placing the fixed portion of
the rail clamp against the accessory rail and
align the rail key with the appropriate cross
groove in the accessory rail.
4. Depress the tension bolt to open the rail clamp, rotate the TLR-3 into place and release the pressure
on the tension bolt to "snap" the light in place.
5. Check for fit and tighten tension bolt until the TLR-3 is securely attached to the firearm.
Rotate tool
A COIN SHOULD BE USED TO OBTAIN SUFFICIENT TIGHTNESS.
and place
over e-clip.
SWITcH OPERATION
The TLR-3 features a paddle switch providing momentary or constant activation.
OFF (PADDLE)
Momentary
MAINTENANcE
The TLR-3 rail clamp tension bolt requires an application of high quality gun oil to keep it rust free. Use a soft
cloth and mild detergent to clean the glass LED lens and keep it free of dirt and grime.
Note: Always avoid aggressive cleaning solutions as they may damage the TLR-3. If you shoot ammunition with
an exposed lead base on the bullets, the lens and facecap may become coated with lead. This may be removed
from the lens by rubbing with fine steel wool. It is extremely difficult to remove the lead coating from the
facecap. Wrap the facecap with electrical tape to avoid lead coating.
STREAMLIGHT LIMITED LIFETIME WARRANTy
Streamlight warrants this product to be free of defect for a lifetime of use. We will repair, replace or refund the
purchase price, at our option, of any Streamlight product that does not work or that you manage to break for as
long as you own it. Of course, this limited lifetime warranty excludes abuse and batteries. Please return your
Streamlight to our factory to take advantage of this guarantee.
SERvIcE
The TLR-3 contains few or no user-serviceable parts.
Please Return To: Customer Service, STREAMLIGHT, INC., 30 Eagleville Road, Eagleville, PA U.S.A. 19403-39996
Phone: (800) 523-7488 Toll-Free, Fax: (800) 220-7007, www.streamlight.com
Constant Momentary
OFF (PADDLE)
Constant