Technical Specifications Of Product - Nice Hyke HK7024 Instructions Et Avertissements Pour L'installation Et L'utilisation

WARNINGS: • All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to apply modifi-
cations to products at any time when deemed necessary, maintaining the same intended use and functionality.
Type
Maximum torque
Nominal torque
Speed under no load
Speed at nominal torque
Maximum cycle frequency
Maximum continuous cycle time
Application limits
Lifetime
Power supply
Backup power supply
Solar power
Maximum absorbed power
Maximum absorbed current
Absorbed power with
"All – Standby (1)" function
when powered by PS124
or SYKCE kit (including
OXI receiver)
Flashing light output [*]
Electric lock output [*]
Gate open indicator output [*]
BLUEBUS output
STOP input
SS input
Radio engage
Radio AERIAL input
Programmable functions
Functions in self-learning
Assembly
Operating temperature
se in acid, saline or
potentially explosive
atmospheres
Protection rating
Dimensions (mm)
Weight (kg)
Notes:
(1) - Function can be activated with Oview programmer.
[*] - The outputs Flashing Light, Electric lock and Gate Open Indicator can be programmed with other functions (see "TABLE 3 – Level 1 functions"; or via the Oview programmer; see
chapter 8.3). The electrical specifications of the output are adapted to the type of selected function: • flashing light function: lamp 12 Vdc, max. 21 W; • electric lock function: 12 Vac
max. 15 VA; • other outputs (all types): 1 lamp or relay 24Vdc (-30 to +50%), max. 4 W.

TECHNICAL SPECIFICATIONS OF PRODUCT

HK7024K
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release. Built-in control unit and OXI radio receiver.
the product can be used on gates with leaf weights up to 330 kg for lengths up to 1.8m or 200 kg
estimated between 150,000 cycles and 500,000 cycles, according to the conditions stated in table 13 and graph 3
230 Vac (120 Vac for version HK7024K/V1)
±10%; 50/60 Hz
Provision for buffer battery PS124
provision for SYKCE kit
300 W
1,5 A (3 A for version HK7024K/V1)
less than 100 mW
one LUCYB flashing light (12 V, 21 W bulb)
one 12 Vac electric lock (max 15 VA)
one 24 V lamp (max. 4 W) (the output voltage
may vary between -30 and +50%, the output can
also control small relays)
one output with load of maximum 15 Bluebus
units (max. 6 pairs of MOFB or MOFOB photocells plus
2 pairs of MOFB or MOFOB photocells routed
as opening devices plus max. 4 MOMB
or MOTB control devices)
for normally closed contacts, normally open
contacts or contacts with constant 8,2 kΩ resistance;
selection of the type of contact is in self-learning
mode and a modification with respect to the memorised
status will generate a "STOP"
for normally open contacts (closure of the contact
generates a Step Step command)
SM connector for receivers in the families SMXI,
OXI and OXIFM
50 Ω for cable type RG58 or similar
8 ON-OFF type functions (Table 3) and
8 settable functions (Table 5)
• Self-learning of devices connected to the BlueBus output.
• Self-learning of the type of device connected to the "STOP"
terminal (NO, NC contact or 8,2 kΩ resistance).
• Self-learning of the gate leaf travel and automatic
calculation of deceleration points and partial opening.
• Self-learning of operation with one or two motors
from -20°C to +50°C (at low temperatures, gearmotor efficiency is reduced)
10.5 Kg;
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release.
500 Nm
120 Nm
2.25 RPM
2.00 RPM
40 cycles/hour
approx. 7 minutes
for lengths up to 3.5m (see graph 1)
Vertical, with dedicated fixing plate
NO
IP 54 (with container intact)
210 x 290 x 320 h
HK7224K
24 Vdc (±10%)
140 W
6 A for a maximum interval of 2 s
9.5 Kg
English – 13