Basic Navigation - Hedson IRT 4-1 PcAuto Mode D'emploi

7. Program mode – General rules for navigation in the software
- The display shows software defined options in the bottom corner fields.
To adjust the values use the arrow keys.
- To move to previous display without saving, press cancel.
7.1

Basic navigation

There are twelve predefined programs and three empty ones. All 15 programs have editable positions, names and
drying parameters. Scroll up or down using the arrow keys, press select to run the program or view to edit.
Stop or cancel
returns to 7.1.
6 6
1. Putty 6. Topcoat
2. Filler Bright 7. Clearcoat
3. Filler Dark 8. Plast Filler
4. Waterbase 9. Plast Topcoat
5. Basecoat 10. Plast Clearcoat
7.2 Run
7.2.1 Distance check
The distance is indicated on the display
as "too close", "too far" or "correct". If
measuring fails "check distance manu-
ally" appears.
Use the buttons on the keyboard to al-
ter between one or two active cassettes
and to turn on/off the temp. control.
See chapter 8.1.
7.2.2 Start drying
Press start to begin the drying se-
quence. The remaining time of the
"flash off" will start counting down.
When the count down is finished, the
program automatically changes to full
bake mode.
7.2.3 Program graph
This graph is available when the tem-
perature control is active. The graph de-
scribes the target, actual temperature,
and remaining time. See chapter 8.1.
7.2.4 Program values
These are the same values as shown
in program graph (7.2.3), except for
the remaining time, but also the used
power capacity of the machine and the
energy consumption of the current dry-
ing process.
Note! An inactive temperature control
does not show temperature values.
7.2.5 Energy consumption
Total energy consumption per drying
process is shown for the last 10 runs.
7.2.6 Drying complete
When flash off and full bake times have
expired the software returns to 7.1.
Note! To extend the lifetime of the
lamps, the ventilators will continue to
run for cooling. After three minutes they
turn off automatically.
Note! When the drying program is
completed the temperature control will
automatically reactivate.
11. Final boost
12. Soft cure
13. Free prog
14. Free prog
15. Free prog
7.3
7.3.1 Properties
The values of the chosen program will
show on the display. By pressing the
"Temperature control" button the software
switches between the properties with and
without the temperature control. A change
in either property is independent of the
Stop or cancel
other one. See chapter 8.1 for more info.
returns to 7.1.
7.3.2 PIN Code
Use the arrow keys to set the correct
digit. Press enter to confirm and to edit
the second, third and fourth digit in the
advanced PIN code.
Note! An entered PIN code is valid for all
entries until the main switch is turned off.
See chapter 9.2 for "advanced PIN code".
Use arrow keys
to set numbers.
7.3.3 Edit program parameters
When marked, change the value of the pa-
rameters with the arrow keys. Press enter to
change the next value and so on. Pressing
enter for the last value directs the user to
editing of program position and name.
Press cancel to exit to 7.3.1 without saving
any parameters.
7.3.4 Edit prog. position/name
The program
When marked, change the program
returns to 7.3.1.
number with the arrow keys. Press enter
to confirm and to edit the next symbol.
Note! Changing the number will also
change the program position in the
program list.
7.3.5 Expansion of the program
When the drying process requires more
than the two standard steps, you can ex-
The program
pand the number of steps in the drying
returns to 7.3.1.
cycle by linking to the next program.
Start from point 7.3.4 and press "Enter"
repeatedly until the "Link to next pro-
gram" appears on the screen. Select
with the arrow keys "Yes" or "No", and
then press "Save". The link to the next
program will remain until it is deacti-
vated (No). Use the program 13, 14 or
15 as these are free programs without
The program
any default.
returns to 7.3.1.
EN
Edit
steps
713687 rev 10