Maintenance And Servicing - Bosch GDR 12V-110 Notice Originale

Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Practical advice
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
The torque depends on the impact duration. The maximum
achieved torque results from the sum of all individual
torques achieved through impact. Maximum torque is
achieved after an impact duration of 6–10 seconds. After
this duration, the tightening torque is increased only minim-
ally.
The impact duration is to be determined for each required
tightening torque. The tightening torque actually achieved
should always be checked with a torque wrench.
Screw applications with hard, spring-loaded or soft seats
When the achieved torques in an impact series are measured
during a test and transferred into a diagram, the result is the
curve of a torque characteristic. The height of the curve cor-
Guide values for maximum screw tightening torques
Figures given in Nm; calculated from the tensional cross-section; utilization of the yield point: 90% (with friction coefficient
µ = 0.12). As a control measure, always check the tightening torque with a torque wrench.
total
Property Classes Standard Screws/Bolts
according to
3.6 4.6
DIN 267
M6 2.71 3.61
M8 6.57 8.7
M10 13 17.5
M12 22.6 30
M14 36 48
M16 55 73
Tips
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
Note: Ensure that no metal particles enter the power tool.
Belt clip (see figure E)
You can use the belt clip (17) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always at hand.
Coloured clip (see figure F)
You can use the coloured clip (18) to individually identify the
power tool.
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Bosch Power Tools
responds to the maximum achievable torque, and the steep-
ness indicates the duration in which this is achieved.
A torque characteristic depends on the following factors:
– Strength properties of the screws/nuts
– Type of backing (washer, disc spring, seal)
– Strength properties of the material being screwed/bolted
together
– Lubrication conditions at the screw/bolt connection
The following application cases result accordingly:
– A hard seat is a metal-to-metal screw application which
uses washers. After a relatively short impact duration, the
maximum torque is achieved (steep characteristic curve).
An unnecessarily long impact duration only causes dam-
age to the machine.
– A spring-loaded seat is also a metal-to-metal screw ap-
plication but uses spring washers, disc springs, studs or
screws/nuts with conical seats. It is also called a spring-
loaded seat when extensions are used.
– A soft seat is a screw application of e.g. metal on wood or
a screw application that uses lead washers or fibre wash-
ers as backing.
For a spring-loaded seat, as well as for a soft seat, the max-
imum tightening torque is lower than for a hard seat. A much
longer impact duration is also required.
5.6 4.8 6.6 5.8
4.52 4.8 5.42 6.02
11 11.6 13.1 14.6
22 23 26 29
37.6 40 45 50
60 65 72 79
92 98 110 122
Only store the battery only within a temperature range of -20
to 50 °C. Do not leave the battery in your car in the summer,
for example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Maintenance and Servicing

Maintenance and cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
High-strength Bolts
6.8 6.9 8.8 10.9
7.22 8.13 9.7 13.6
17.5 19.7 23 33
35 39 47 65
60 67 80 113
95 107 130 180
147 165 196 275
1 609 92A 4JJ | (03.09.2018)
English | 17
12.9
16.2
39
78
135
215
330