Bosch GDS Professional 18 V-EC 250 Notice Originale page 13

Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Tool holder
(2) Carrying strap
A)
(3) Belt clip
A)
(4) Battery
A)
(5) Battery release button
(6) Rotational direction switch
(7) On/off switch
(8) "PowerLight" lamp
(9) Handle (insulated gripping surface)
(10) Application tool (e.g. impact socket)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless impact screw-
driver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard
screwdriving application ac-
cording to ISO 5393
Machine screw diameter
Tool holder
Weight according to EPTA-
Procedure 01:2014
Permitted ambient temperat-
ure
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) Only for inductive batteries
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-2.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 100 dB(A); sound power level
111 dB(A). Uncertainty K = 3 dB.
Bosch Power Tools
Wear hearing protection
Total vibration values a
determined according to EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
a = 18 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to compare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The given vibration level and noise emission value represent
the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
GDS 18 V-EC 250 This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
3 601 JD8 1..
ator from the effects of vibration, such as servicing the
V = 18
power tool and application tools, keeping the hands warm,
rpm 0–2400
and organising workflows correctly.
rpm 0–3400
Assembly
Nm 250
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
M10 – M18
changing tool, etc.). The battery should also be re-
■ ½"
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
A)
kg 1.6–2.0
Battery Charging
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
°C 0... +45
your power tool.
°C –20... +50
Note: The battery is supplied partially charged. To ensure
the maximum performance of the battery, use the charger to
GBA 18V..
fully charge the battery before first use.
GBA 18V...W
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
AL 18..
does not damage the battery.
GAL 3680
C)
GAL 18...W
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). When the battery is
discharged, the power tool is switched off by means of a pro-
tective circuit: The application tool stops moving.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
(triax vector sum) and uncertainty K
h
2 2
, K = 1.5 m/s ,
1 609 92A 4PN | (12.10.2018)
English | 13