Parts List - Rona RNS-18G-001 Guide D'utilisation

Problem
Tool skips fasteners
Fasteners jam in tool or magazine
Tool will not drive fasteners down tight
ITEM DESCRIPTION
RNS-18G-001-1 Screw
RNS-18G-001-2 Bushing
RNS-18G-001-3 Exhaust cover
RNS-18G-001-4 Washer
RNS-18G-001-5 Screw
RNS-18G-001-6 Cylinder cap
RNS-18G-001-7 Gasket
RNS-18G-001-8 Cylinder extension
RNS-18G-001-9 Seal
RNS-18G-001-10 Spring
RNS-18G-001-11 O-ring 15.7 X 2
RNS-18G-001-12 O-ring 38.3 X 3
RNS-18G-001-13 Valve
RNS-18G-001-14 O-ring 36.3 X 3.5
RNS-18G-001-15 Stopper washer
RNS-18G-001-16 O-ring 50.5 X 2.5
RNS-18G-001-17 Collar
RNS-18G-001-18 O-ring 30.3 X 3
RNS-18G-001-19 Piston assembly
RNS-18G-001-20 O-ring 40.2 X 2.3
RNS-18G-001-21 O-ring 35.6 X 1.8
RNS-18G-001-22 Cylinder
RNS-18G-001-23 Bumper
RNS-18G-001-24 Body
TROUBLESHOOTING
Cause
1. Worn bumper or damaged spring
2. Dirt in front plate
3. Inadequate airflow to tool
4. Worn or dry O-ring on piston
5. Damaged O-ring on trigger valve
6. Cylinder cap is leaking
1. Joint guide is worn
2. Fasteners are the wrong size or damaged
3. Magazine or front plate screws are loose
4. Blade in piston assembly is damaged
1. Worn blade in piston assembly
2. Lack of power
3. Slow cycling and loss of power

PARTS LIST

Please refer to the Schematic Drawing on p. 17 for the location of parts.
Solution
1. Replace bumper or pusher spring
2. Clean drive channel of front plate
3. Check hose and compressor fittings
4. Replace O-ring or lubricate
5. Replace O-ring
6. Replace seal
1. Replace joint guide
2. Use only the recommended and undamaged
fasteners
3. Tighten all screws
4. Replace piston assembly
1. Replace Piston assembly
2. Adjust regulator to adequate air pressure
3. Check cylinder cap spring for broken coils or
reduced length or if exhaust port of cylinder
cap is restricted
ITEM DESCRIPTION
RNS-18G-001-25 Joint guide
RNS-18G-001-26 Safety guide
RNS-18G-001-27 Spring
RNS-18G-001-28 Safety bracket
RNS-18G-001-29 Safety bracket assembly
RNS-18G-001-30 Pin
RNS-18G-001-31 Seal
RNS-18G-001-32 Trigger valve head
RNS-18G-001-33 Spring
RNS-18G-001-34 O-ring 5.5 X 1.5
RNS-18G-001-35 Trigger valve stem
RNS-18G-001-36 O-ring 15 X 1.9
RNS-18G-001-37 Trigger vavle guide
RNS-18G-001-38 Trigger spring
RNS-18G-001-39 Trigger
RNS-18G-001-40 Pin
RNS-18G-001-41 Lock washer
RNS-18G-001-42 Pin
RNS-18G-001-43 Plate
RNS-18G-001-44 Screw
RNS-18G-001-45 Latch assembly
RNS-18G-001-46 Pin
RNS-18G-001-47 Front plate
RNS-18G-001-48 Bar guide
15
070601