Noise/Vibration Information; Charging The Battery - Bosch UniversalImpact 18 Notice Originale

Cordless drill/driver
Rated voltage
No-load speed
– 1st gear
– 2nd gear
Impact rate
Max. torque, hard/soft
screwdriving application ac-
cording to ISO 5393
Max. drilling diameter (1st/2nd gear)
– Steel
– Wood
Max. screw diameter
Tool holder
Max. impact drilling diameter
Weight according to
EPTA-Procedure 01:2014 A)
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation B) and
during storage
Recommended batteries
Recommended chargers C)
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
97 dB(A). Uncertainty K=5 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
Drilling into metal: a <2.5 m/s 2 , K=1.5 m/s
h
Impact drilling into concrete: a =18 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
Bosch Power Tools
To estimate vibration and noise emissions accurately, the
UniversalImpact 18
times when the tool is switched off or when it is running but
V= 18
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
min -1 0–400
Implement additional safety measures to protect the oper-
min -1 0–1 350
ator from the effects of vibration, such as servicing the
min 0–20 250
-1
power tool and application tools, keeping their hands warm,
Nm 30/18
and organising workflows correctly.
Assembly
u
mm 10
mm 30
mm 8
mm 10
mm 6

Charging the Battery

kg 1.3–1.6
u
°C 0 to +35
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
°C –15 to +50
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
PBA 18V...W-.
does not damage the battery.
AL 18...
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Removing the battery
2
2 , K=3 m/s 2
To remove the battery , press the battery release button and
pull the battery to the rear and out of the power tool. Do not
use force to do this.
Changing the tool (see figure A)
u
The drill spindle is locked when the on/off switch (9) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Wear protective gloves when changing tools. There is
a risk of injury when touching the application tools.
1 609 92A 5L3 | (28.02.2020)
English | 13