Bosch GSA 18 V-LI Professional Notice Originale page 14

14 | English
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
A)
(1) Saw blade
(2) Adjustable base plate
(3) Saw blade receptacle
(4) Locking sleeve for saw blade
(5) Stroke speed selector switch
(6) On/off switch
A)
(7) Battery release button
A)
(8) Battery
(9) Handle (insulated gripping surface)
(10) Button for battery charge indicator
A)
(11) Battery charge indicator
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Reciprocating saw
Article number
Stroke rate control
Rated voltage
No-load stroke rate n
0
– First gear
– Second gear
Tool holder
Stroke
Max. cutting depth
– In wood
– In steel (unalloyed)
– Pipe diameter
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– During charging
B)
– During operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.
1 609 92A 4TG | (05.04.2019)
Noise/vibration information
Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85 dB(A); sound power level
96 dB(A). Uncertainty K=5 dB.
Wear hearing protection
Vibration total values a
determined according to EN 62841-2-11:
Cutting boards with saw blade S 644 D:
a
Cutting wooden beams with saw blade S 611 DF:
a
The vibration level and noise emission value given in these
A) instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
GSA 18 V-LI
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
3 601 F4J 0..
working period.
●
To estimate vibration and noise emissions accurately, the
V= 18
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
−1
min 0–2400
over the total working period.
−1
min 0–2700
Implement additional safety measures to protect the oper-
SDS
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
mm 28
and organising workflows correctly.
mm 250
Assembly
mm 20
u
mm 130
A)
kg 3.2–4.2
°C 0 to +45
Battery Charging
°C −20 to +50
u
GBA 18V...
ProCORE18V...
Note: The battery is supplied partially charged. To ensure
GAL 18...
full battery capacity, fully charge the battery in the charger
GAX 18...
before using your power tool for the first time.
GAL 36...
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
(triax vector sum) and uncertainty K
h
2 2
=27.5 m/s , K=1.5 m/s ,
h,B
2 2
=27.5 m/s , K=1.5 m/s .
h,WB
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Bosch Power Tools