EINHELL GC-PC 2040 I Mode D'emploi D'origine page 23

Masquer les pouces Voir aussi pour GC-PC 2040 I:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 35
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
2. Layout and items supplied
2.1 Layout (Fig. 1-21)
1. Motor unit
2. Chain bar
3. Saw chain
4. Chain guard
5. Spark plug wrench
6. Front hand guard (chain brake lever)
7. Front handle
8. Rear handle
9. Starter handle
10. On/Off switch
11. Throttle lever
12. Throttle lever safety lock
13. Choke lever
14. Air fi lter cover
15. Air fi lter
16. Spark plug
17. Stop claw
18. Chain catch
19. Chain bar fastening nut
20. Chain tensioning screw
21. Fuel tank cap
22. Oil tank cap
23. Mixing container
24. Screwdriver
Anl_GC_PC_2040_I_SPK7.indb 23
Anl_GC_PC_2040_I_SPK7.indb 23
GB
25. Fuel pump (primer)
Safety features (fi g.1a/1b)
3
LOW KICKBACK SAW CHAIN helps signi-
fi cantly reduce kickback, or the intensity of
kickback, due to specially designed depth
gauges and guard links.
6
CHAIN BRAKE LEVER / HAND GUARD
protects the operator's left hand in the event it
slips off the front handle while saw is running.
CHAIN BRAKE is a safety feature designed
to reduce the possibility of injury due to
kickback by stopping a moving saw chain
in milliseconds. It is activated by the CHAIN
BRAKE lever.
10 STOP SWITCH immediately stops the engine
when tripped. Stop switch must be pushed to
ON position to start or restart engine.
12 SAFETY TRIGGER prevents accidental
acceleration of the engine. Throttle trigger
cannot be squeezed unless the safety latch is
depressed.
18 CHAIN CATCHER reduces the danger of
injury in the event saw chain breaks or derails
during operation. The chain catcher is desig-
ned to intercept a whipping chain.
Note: Study your saw and be familiar with its
parts.
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
Open the packaging and take out the equip-
ment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
If possible, please keep the packaging until
the end of the guarantee period.
- 23 -
11.08.2016 15:17:52
11.08.2016 15:17:52

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Gc-pc 2040/145.018.5145.018.52

Table des Matières