Pole Chain Saw; Safety Instructions - IKRA IPM 33 TL Manuel D'utilisation

5. POLE CHAIN SAW

Parts and Controls
8
1 = Saw Chain
2 = Guide Bar
3 = Oil Tank
4 = Oil Filler Cap
5 = Drive tube
6 = Chain Sprocket Cover
7 = Chain catch bolt
8 = Chain Guard (Scabbard)

SAFETY INSTRUCTIONS

A) TRAINING
1) Read the instructions carefully. Become acquainted
with the controls and the proper use of the machine.
Learn how to stop the engine quickly.
2) Only use the machine for the purpose for which it was
designed, that is "limbing trees with dimensions suit-
able for the length of the bar" or wooden objects with
the same characteristics. Any other use may be dan-
gerous and damage the machine.
3) Never allow children or persons unfamiliar with these
instructions to use the machine.Local regulations may
restrict the age of the operator.
4) The machine must never be used by more than one
person.
5) Never use the machine :
- when people, especially children or pets are in the
vicinity;
- if the user is tired or unwell, or has taken medicine,
drugs, alcohol or any substances which may slow
his reflexes and compromise his judgement;
- if the user is not capable of holding the machine
firmly with two hands and/or of remaining standing
on the ground whilst working.
6) Remember that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
B) PREPARATION
1) Before using the machine, check its general condi-
tion.
2) Always wear adequate clothing when using the ma-
chine which do not hamper movements in any manner.
1
2
4
3
7
6
- Always wear slim-fitting protective clothing, fitted
with shear-proof protection devices.
- Always wear protective gloves and eye-goggles
and safety anti-shear boots with non-slip soles.
- Always wear ear and hearing protection devices.
- Never wear scarves, shirts, necklaces, or any hang-
ing or flapping accessory that could catch in the ma-
chine or in any objects or materials in the work area.
- Tie your hair back if it is long.
3) Before starting your work,make sure that all the pro-
tection devices are correctly fitted.
C) OPERATION
1) Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
2) Work only in daylight or good artificial light.
3) Take on a firm and well-balanced position:
- where possible avoid working on wet slippy ground
5
or in any case on uneven or ripid ground which does
not guarantee stability for the operator;
- avoid using unstable ladders or platforms;
- never run, but walk carefully paying attention to the
lay of the land and any eventual obstacles.
4) Check that when the machine is running idle,there
is no movement of the chain and, after pressing the
throttle trigger, the engine quickly returns to minimum
speed.
5) Take care not to hit the bar hard against foreign ob-
jects or flying debris caused by the movement of the
chain.
D) MAINTENANCE AND STORAGE
1) Keep all nuts, bolts and screws tightly fastened to
be sure the equipment is in safe working condition.
Routine maintenance is essential for safety and for
maintaining a high performance level.
2) Always wear protective gloves when handling the cut-
ting device.
3) Make sure the chain is well sharpened. Any work on
the chain and bar require specific experience and
special tools. For safety purposes, we recommend
you contact your dealer to ensure work is done cor-
rectly.
4) For safety reasons, never use the machine with worn
or damaged parts. Damaged parts are to be replaced
and never repaired. Only use original spare parts.
Parts that are not of the same quality can seriously
damage the equipment and compromise safety.
5) Store the machine out of the reach of children!
E) TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled or transport-
ed you must:
- turn off the engine, wait for the chain to stop and
disconnect the spark plug cap;
- mount the bar cover;
- only hold the machine using the handgrips and po-
sition the bar in the opposite direction to that used
during operation.
2) When using a vehicle to transport the machine, posi-
tion it so that it can cause no danger to persons and
fasten it firmly in place to avoid it from tipping over,
which may cause damage or fuel spillage.
GB-21