Intended Use; Technical Data; Before Starting The Equipment - EINHELL GE-CL 36 Li E Mode D'emploi

Separately available accessories
18V 1.5Ah P-X-C lithium-ion battery
18V 2.0Ah P-X-C lithium-ion battery
18V 2.6Ah P-X-C Plus lithium-ion battery
18V 3.0Ah P-X-C lithium-ion battery
18V 4.0Ah P-X-C lithium-ion battery
18V 5.2Ah P-X-C Plus lithium-ion battery
18V P-X-C charger
Explore battery + charger options at
einhellUSA.com

3. Intended use

The leaf blower/vac is designed to handle only
foliage and garden refuse such as grass and
small branches. Any other use is prohibited.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............. 36 V
No load speed: ................ 8000-13000 rpm (min
Mode conversion: ....... Blower / mulching vacuum
Air speed max: ......................130 mph (210 km/h)
Vacuum air fl ow max: ........... 424 cfm (12 m³/min)
Blower air fl ow max: .......... 115 cfm (3.25 m³/min)
Mulch reduction ratio: .................................... 10:1
Bag capacity: ..................................11.9 gal (45 l)
Weight: ...................................... 7.45 lbs (3.38 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
Anl_GE_CL_36_Li_E_SPK7_USA.indb 10 Anl_GE_CL_36_Li_E_SPK7_USA.indb 10
EN
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the batteries before making
adjustments to the equipment.
5.1. Mounting the suction tube (Fig. 3-7)
•
Slot the front and rear suction tube (Fig. 3)
together and secure with the screw (Fig. 4/
Item 12).
•
Now slide the complete suction tube into the
(2x 18V)
motor housing (Fig. 5) and secure with the
)
-1
screws (Fig. 6/ Item 12).
•
Fit the two wheels (Fig. 8/Item 9) into the
wheel support (Fig. 8/ Item 11). Make sure
that there is an audible click when they
engage.
•
Slide the wheel support (Fig. 9/Item 11) onto
the front suction tube as far as the stop (Fig.
9/Item 14) and fasten it with the screw (Fig. 9/
Item 13).
Note: Please note that the two suction tubes
must always be joined together before they
are mounted on the motor housing, and
that they must never be taken apart when
mounted!
- 10 -
25.04.2019 13:50:36 25.04.2019 13:50:36