Troubleshooting - Maytag MHW7100D Guide D'utilisation Et D'entretien

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.maytag.com/product_help –
If you experience
Error Code Appears in Display
Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.
"Sud"
(Excess suds)
appears in display
Lo followed by FL or F8
followed by E1 (water
supply error) appears in
display
F09 E01
followed by
(drain pump system
error) appears in display
F05 E02
followed by
(door will not lock)
appears in display
"rL"
(remove load) appears
in display
Washer making error beeps
Washer beeps when START
is touched
F## E##
code other than
as described above appears
in display
"Int" (interrupted) appears in
display
Clean Washer LED flashing
at end of wash cycle
16
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Possible Causes
Excessive suds in washer. Washer is
running a suds reduction routine.
Check for proper water supply.
Check plumbing for correct drain
hose installation. Drain hose extends into
standpipe farther than 4 ⁄ " (114 mm).
1
2
Not using HE detergent or using too
much HE detergent.
Washer door not locking.
Load detected in drum during Clean
Washer with affresh cycle.
®
Door has not been opened and closed
for at least 3 cycles.
Door not closed.
System error code.
The cycle was paused or cancelled.
The washer has run 30 wash cycles and
is indicating a reminder to run the Clean
Washer with affresh cycle.
®
Solution
Allow the washer to continue. Use only HE detergent. Always
measure detergent, and base detergent quantity on load size.
Follow detergent manufacturer's instructions.
Unit will drain for 8 minutes while door remains locked. When
complete, touch POWER/CANCEL once to clear the code.
Then touch POWER/CANCEL again to restart washer. If code
appears again, call for service.
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
If used, auto shut off connectors and hoses must be properly
installed and in working order.
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor.
Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level.
Touch POWER/CANCEL to cancel the cycle. Make sure the
door is closed completely and latching. Check for items in
the washer drum that may be keeping the door from closing
completely.
Remove items from washer drum and restart Clean Washer with
affresh cycle.
®
This code may appear when the washer is first turned on.
Open and close the door to clear the display.
Close the door completely.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears
again, call for service.
The washer can take 20 to 30 minutes to stop spinning
and drain and will display this error code during that time.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer.
Run the Clean Washer with affresh
with affresh cycle is not turned on, the LED will stop flashing
®
at the end of a wash cycle after running 3 more regular wash
cycles. After 30 more wash cycles are completed, the Clean
Washer LED will again flash at the end of a wash cycle as a
reminder.
cycle. If the Clean Washer
®