Bosch GWS 18V-10 Professional Notice Originale page 24

24 | English
A plastic part (O-ring) is fitted around the cent-
ring collar in the mounting flange (9). If the O-
ring is missing or damaged, the mounting
flange (9) must be replaced before operation
can resume.
After fitting the abrasive tool, check that the abrasive
u
tool is fitted correctly and can turn freely before
switching on the power tool. Make sure that the abras-
ive tool does not brush against the protective guard or
other parts.
Grinding/Cutting Disc with Diameter 100 mm
The quick clamping nut with bar (11) is not recommen-
ded to be used with 100 mm cutting/grinding disc.
Pay attention to the dimensions of the abrasive tools. The
diameter of the hole must match that of the hub flange. Do
not use an adapter or reducer.
When using diamond cutting discs, ensure that the arrow in-
dicating the direction of rotation on the diamond cutting disc
matches the direction of rotation of the power tool (see the
direction of rotation arrow on the machine head).
See the graphics page for fitting instructions.
To fasten the grinding/cutting disc, screw on the clamping
nut (12)and tighten with the two-pin spanner.
After fitting the abrasive tool, check that the abrasive
u
tool is fitted correctly and can turn freely before
switching on the power tool. Make sure that the abras-
ive tool does not brush against the protective guard or
other parts.
Flap disc
Always fit the hand guard (17) when working with the
u
flap disc.
Rubber Sanding Pad
Always fit the hand guard (17) when working with the
u
rubber sanding pad (18).
See the graphics page for fitting instructions.
Slide the rubber sanding pad (18) onto the grinding spindle
(16).
Press the sanding sheet (19) firmly onto the underside of
the rubber sanding pad (18).
Screw on the round nut (20) and tighten with a two-pin
spanner.
Cup brush/disc brush
Always fit the hand guard (17) when working with the
u
cup brush or disc brush.
See the graphics page for fitting instructions.
The cup brush/disc brush must be screwed onto the grinding
spindle until it rests firmly against the grinding spindle flange
at the end of the grinding spindle thread. Tighten the cup
brush/disc brush with an open-ended spanner.
Approved abrasive tools
You can use all the abrasive tools mentioned in these operat-
ing instructions.
1 609 92A 6KF | (07.06.2021)
-1
The permissible speed [min ] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
max. [mm]
D b
100 7
115 7
125 7
100 –
115 –
125 –
75 30
82 –
Rotating the Machine Head (GWS 18V-10)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
chine head carefully, without removing it from the hous-
ing, into the new position. Screw in and retighten the four
screws.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
[mm]
-1
d [min ] [m/s]
16 9000 80
22.2 9000 80
22.2 9000 80
– 9000 80
– 9000 80
– 9000 80
M 14 9000 45
M 14 9000 80
The machine head can be
rotated in 90° increments.
In this way, the on/off
switch can be brought into
a more favourable handling
position for particular ap-
plications, e.g. for left-
handed tool users.
Completely unscrew the
four screws. Rotate the ma-
Bosch Power Tools