Features And Functions; Preparations Before Use; Getting Accurate Readings; Automatic Shut-Down Function - Tanita InnerScan 50 Mode D'emploi

Features and functions
1. Display
Screen
3. Features
Buttons
4. Heel
Electrodes
7. Personal keys
Preparations before use
Inserting the Batteries
Turn the scale over and remove the battery cover by releasing the latch, install 2 pieces of new
battery (included) with correct polarity as indicated.
Note: B e sure that the polarity of the batteries is set properly. If the batteries are incorrectly
positioned the fluid may leak and damage floors. If you do not intend to use this unit for
a long period of time, it is advisable to remove the batteries before storage.
Please note that the included batteries from factory may have decreased energy levels over time.
Positioning the Monitor
Place the measuring platform on a hard, flat surface where there is minimal vibration to ensure
safe and accurate measurement.
Use carpet feet when the scale is used on soft surface, such as rugs or carpetings.
Note: T o avoid possible injury, do not step on the edge of the platform.
Do not use the carpet feet on hard, flat surface as the unit may chip over.
Handling Tips
This monitor is a precision instrument utilizing state-of-the-art technology.
To keep the unit in the best condition, follow these instructions carefully:
• Do not attempt to disassemble the measuring platform.
• Store the unit horizontally, and place it so that the buttons will not be pressed accidentally.
• Avoid excessive impact or vibration to the unit.
• Place the unit in an area free from direct sunlight, heating equipment, high humidity, or extreme temperature change.
• Never submerge in water. Use alcohol to clean the electrodes and glass cleaner (applied to a cloth first) to keep them shiny;
avoid soaps.
• Do not step on the platform when wet.
• Do not drop any objects onto the platform.
• Do not use this scale while operation transmitters (such as a cell phone) as this may affect your results.

2. Ball-of Foot 5. Set Button
Electrodes
8. Weight-Only
6. Arrow (Select) Buttons
Key
Accessories
10. Carpet Feet (4)
9. Lithium Batteries
CR2032 (2)
Open as shown.
Direction of the batteries.
For use on carpeting or
rugs only of thickness
up to 0.4" (10 mm)
Getting accurate readings
To ensure accuracy, readings should be taken without clothing and under consistent conditions of hydration. If you do not
undress, always remove your socks or stockings, and be sure the soles of your feet are clean before stepping on the measuring
platform. Be sure that your heels are correctly aligned with the electrodes on the measuring platform. Don't worry if your feet
appear too large for the unit -accurate readings can still be obtained if your toes overhang the platform.
It is best to take readings at the same time of day. Try to wait about three hours after rising, eating, or hard exercise before taking
measurements.
While readings taken under other conditions may not have the same absolute values, they are accurate for determining the
percentage of change as long as the readings are taken in a consistent manner. To monitor progress, compare weight and body fat
percentage taken under the same conditions over a period of time.
Heels centered on Toes may overhang
electrodes measuring platform
Automatic shut-down function
The automatic shut-down function shuts off the power automatically in the following cases:
• If you interrupt the measurement process, the power will shut down automatically within 10 to 20 seconds, depending upon the
type of operation.
• If an extreme weight is applied to the platform.
• During programming, if you do not touch any of the keys or buttons within 60 seconds.*
• After you have completed the measuring process.
Note: I f the power shuts off automatically, repeat the steps from "Setting and storing personal data in memory" (p.4).
Switching the weight mode
Note : For use only with models containing the weight mode switch
You can switch the unit indication by using the switch on the back of the scale as
shown in the figure.
The unit should be turned on to switch the weight mode.
Note: If weight mode is set to pounds or stone-pounds, the height programming mode
will be automatically set to feet and inches.
Similarly, if kilograms is selected, height will be automatically set to centimetres.
Note: A n accurate reading will not be possible if
the soles of your feet are not clean, or if your
knees are bent or you are in a sitting position.