Berner BACOT 12V STARLOCK Notice Originale page 18

Cordless oscillator
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes
with the product.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-4.
Typically, the A-weighted sound pressure level of
the power tool is 79 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed
80 dB(A).
Wear hearing protection!
Total vibration values a (triax vector sum) and un-
h
certainty K determined according to
EN 62841-2-4:
2
Sanding: a =3 m/s , K=1.5 m/s
h
sawing with plunge cut saw blade: a
K=1.5 m/s 2 ,
sawing with segment saw blade: a
2
K=1.5 m/s ,
scraping: a =8.5 m/s 2 , K=1.5 m/s
h
The vibration level and noise emission value given
in these instructions have been measured in ac-
cordance with a standardised measuring proced-
ure and may be used to compare power tools.
They may also be used for a preliminary estima-
tion of vibration and noise emissions.
The stated vibration level and noise emission
value represent the main applications of the
power tool. However, if the power tool is used for
other applications, with different application tools
or is poorly maintained, the vibration level and
noise emission value may differ. This may signific-
antly increase the vibration and noise emissions
over the total working period.
To estimate vibration and noise emissions accur-
ately, the times when the tool is switched off or
when it is running but not actually being used
should also be taken into account. This may signi-
ficantly reduce vibration and noise emissions over
the total working period.
Implement additional safety measures to protect
the operator from the effects of vibration, such as
servicing the power tool and application tools,
keeping their hands warm, and organising work-
flows correctly.
18 | English
Fitting
BACOT 12V
STARLOCK
Remove the battery from the power tool be-
u
BBP 12 V
fore carrying out work on the power tool (e.g.
2.0 Ah
maintenance, changing tool, etc.). The bat-
BBP 12 V
tery should also be removed for transport and
4.0 Ah
storage. There is risk of injury from unintention-
BBC 12 V
ally pressing the on/off switch.
Battery Charging
Use only the chargers listed in the technical
u
data. Only these chargers are matched to the
lithium-ion battery of your power tool.
English
Note: The battery is supplied partially charged. To
ensure full battery capacity, fully charge the bat-
tery in the charger before using your power tool
for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging process does not damage the battery.
The lithium-ion battery is protected against deep
discharge by the "Electronic Cell Protection
(ECP)". When the battery is discharged, the power
tool is switched off by means of a protective cir-
2
,
cuit: The application tool no longer rotates.
2
=9 m/s ,
h Do not continue to press the On/Off switch
u
after the power tool has automatically
2
=2.5 m/s ,
switched off. The battery can be damaged.
h
To remove the battery (3), press the battery re-
2 .
lease button (2) and pull the battery to the rear
and out of the power tool. Do not use force to do
this.
Battery charge indicator
The three green LEDs on the battery charge indic-
ator (6) indicate the state of charge of the battery
(3). The battery charge indicator only lights up for
five seconds after start-up.
LED
Continuous lighting 3x green ≥2/3
Continuous lighting 2x green ≥1/3
Continuous lighting 1x green <1/3
Flashing light 1x green
Flashing light 3x green
If no LED lights up after switching the power tool
on, then the battery is defective and must be re-
placed.
Changing the tool
Wear protective gloves when changing tools.
u
There is a risk of injury when touching the ap-
plication tools.
English
English
English
Capacity
Reserve
Empty
English
1 609 92A 4RW • 17.12.18