Publicité
Les langues disponibles
Les langues disponibles
Installing and Removing the Battery Pack
(Fig. D)
DO NOT USE THIS HOOD LIGHT WITH A BATTERY
GREATER THAN 12 AH CAPACITY.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
release button
8
and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Power ON/OFF Button (Fig. A)
1. To turn the light on, press the power button
setting is high mode.
2. Press the button again and the light will convert to
low mode.
3. Press again to turn the light off.
Low Battery Indicator (Fig. A)
As the battery
7
nears a fully discharged state, the light will
blink twice and then dim, dropping the brightness of the
light below the normal level. The light will continue to blink
twice every 45 seconds until the battery is fully discharged
at which time the light will turn off. Indication time will vary
based on battery pack capacity.
Light Selector Button (Fig. A)
The hood light can operate using one or both LED lenses.
1. With the light on, press the light selector button
cycle between left, right or both LED lenses
Attaching Hood Light to Auto Hood
(Fig. A, E, F)
CAUTION: Ensure area between extended hook and
hood light is clear before releasing hook. Keep your
fingers out of the area between the hook and the light
when it retracts.
CAUTION: User must confirm that the hood can
support the weight of this light, 9 lbs (4 kg).
1. Unfold the hood light.
2. Attach the hook
1
on one side of the light to the hood
of the automobile, then carefully pull on the other hook
so that it extends out from the housing.
3. Once the hooks extends past the edge of the hood,
slowly allow the hook to slide back into the housing (do
not release the hook) until it securely attaches to the
hood of the automobile.
nOTE: Before installing onto the hood, make sure
the hood is properly secured in the open position via
manufacturer's recommendation.
7
into the tool handle, align
2
, this initial
3
6
.
Adjusting the Orientation of the Light (Fig. F)
Once attached to the automobile hood, the light can be
rotated to the desired position. The rotating mechanisms are
located in the base of each hook
Hood Light Storage (Fig. E, G)
CAUTION: Keep fingers clear of center hinge when
opening or closing hood light.
The hood light folds down for easy, compact storage.
1. Ensure center joint is clear of obstruction before folding.
2. To secure folded hood light, align tab
until they snap together.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
to
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed by a
D
WALT factory service center or a D
e
service center. Always use identical replacement parts
English
1
.
4
to receiver
5
WALT recommended
e
WALT authorized
e
7
Publicité
