Pioneer DDJ-SX2 Mode D'emploi page 13

8 Channel fader
9 Crossfader Assign Switch
a MASTER LEVEL control
b BOOTH MONITOR LEVEL control
c HEADPHONES MIX control
d MASTER CUE button
e Crossfader
f HEADPHONES LEVEL control
g INPUT SELECT switch
h CROSS FADER CURVE selector switch
1 Set the positions of the controls, etc., as shown
below.
Names of controls, etc.
MASTER LEVEL control
TRIM control
EQ (HI, MID, LOW) controls
FILTER control
Channel fader
Crossfader Assign Switch
INPUT SELECT switch
2 Press the [ ] button to play the track.
SYNC OFF
CUE LOOP SAVED LOOP SLICER LOOP
3 Move the channel fader away from you.
4 Turn the [TRIM] control.
Adjust [TRIM] so that the orange indicator on the channel level indicator
lights at the peak level.
5 Turn the [MASTER LEVEL] control to adjust the audio
level of the speakers.
Adjust the sound level output from the [MASTER OUT 1] and [MASTER
OUT 2] terminals to an appropriate level.
Monitoring sound with headphones
Set the positions of the controls, etc., as shown below.
Names of controls, etc.
HEADPHONES MIX control
HEADPHONES LEVEL control
1 Press the headphones [CUE] button for the channel 1.
2 Turn the [HEADPHONES LEVEL] control.
Adjust the sound level output from the headphones to an appropriate
level.
Note
This unit and the Serato DJ software include a variety of functions
enabling individualistic DJ performances. For details on the respective
Position
Turned fully counterclockwise
Turned fully counterclockwise
Center
Center
Moved forward
[THRU] position
[PC] position
INST. DOUBLES INST. DOUBLES INST. DOUBLES INST. DOUBLES
FLIP
SLOT REC START
SAVE LOOP ON/OFF
SYNC OFF
VELOCITY SAMPLER CUE
4 BEAT
Position
Center
Turned fully counterclockwise
functions, see the operating instructions and the Serato DJ software
manual.
This unit's operating instructions can be downloaded from the
Pioneer DJ support site. For details, see Acquiring this unit's
Operating Instructions (p. 3 ).
The Serato DJ software manual can be downloaded from "Serato.com".
For details, see Downloading the Serato DJ software manual (p. 3 ).
Quitting the system
1 Quit Serato DJ.
When the software is closed, a message for confirming that you want to
close it appears on the computer's screen. Click [Yes] to close.
2 Press the [STANDBY/ON] switch on this unit's rear
panel to set this unit's power to standby.
3 Disconnect the USB cable from your computer.
About the AC adapter
Safety instructions
To ensure your personal safety and to maximize the full operating poten-
tial of your unit, read and follow these safety instructions.
Read & Retain Instructions
Read all operating and user information provided with this product.
Cleaning
Use a damp cloth to clean the exterior housing. Avoid using any fluids
including liquid, aerosol or alcohol-based cleaning products.
Water or Moisture
Avoid operating or locating this product near water or other sources of
fluid.
Accessories
Do not place this product on an unstable cart, stand, or table. The prod-
uct may fall and be seriously damaged.
Ventilation
Do not block or cover this product in use. This unit should not be placed
in a built-in installation unless properly ventilated.
Environment
Avoid placing this product in a location with exposure to large quantities
of dust, high temperatures, high humidity, or subject to excessive vibra-
tions or shocks.
Power Sources
Operate this product only from the recommended power sources. If
you are unsure of the power source, consult an authorized Pioneer
representative.
Power-Cord Protection
When unplugging the unit, pull on the plug – not on the cord. Do not
handle the cord or plug with wet hands; doing so could cause an electric
short or shock. Do not allow anything to pinch or rest on the power cord
and do not place in a walkway.
13
En