Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EN
40
10. Accessories
10.1 Measuring adapter MA 2
For the easy measurement of photoelectric current for burner adjustment
and/or troubleshooting, we recommend the use of a special measuring
adapter MA2 (order no. 10042.00010).
The MA 2 measuring adapter is connected between the connector of the
photo conductive cell. The measuring cables of the adapter are sufficiently
long and can be directly and easily connected to the amperemeter.
10.2 Knurled-head screw for dismantling the
diaphragm valve
For the easy disassembly of the diaphragm valve from the oil pre-heater,
we recommend the use of a special knurled-head screw (order no.
10023.00026).
10.3 Portable pump tester
For de-aerating the intake pipe as well as for measuring the injection /
intake pressure of the pump, we recommend the instruments from our
portable pump tester (order no. 10042.00001).
It includes:
1 Case coated with foamed material
2 Pressure gauge (0 - 25 bar)
3 Vacuum gauge (-1 - 0 bar
4 Flexible pressure gauge extension with
1/8" screw-in nipple
5 De-aeration device 1/8" with shut-off
6 Reducing adaptor with 8 x 2mm O-ring
7 Reducing adaptor for pressure gauge
with 8 x 2mm O-ring
3
2
4
1
10.4 Intake silencer
For operation dependent on ambient air, the protective cover at the blower
inlet can be replaced by a intake air silencer which is available as an
accessory (order no. 10003.00167). The sound-reducing internal shape in
combination with the noise-absorbing lining of the intake silencer allows
for the effective reduction of the intake air noise. Due to its flat design, the
silencer can also be used when the hood is installed. The intake silencer
can be installed in the factory or using the conversion kit (order no.
10003.00167) mentioned below.
It includes:
1 Cylinder head screw with SW4 hexagon socket
similar to DIN 912 M4x50
2 Intake silencer
3 Insulating foam, inside
4 Insulating foam, outside
10.5 Sliding flange with additional O-ring sealing
In order to meet utmost requirements regarding odour escaping from the
interface between burner and heat generator, we recommend the use of
a sliding flange connection with additional O-ring sealing. In order to
achieve utmost tightness, the standard flat sealing for the boiler is
supplemented by an additional O-ring sealing. The O-ring sealing can be
installed in the factory or using the conversion kit (order no. 10003.00172)
mentioned below.
The conversion kit includes:
1 Sliding flange for burner
10042.00008
2
Hexagon nut DIN 934 M8
10042.00002
3
Sliding flange S1 for boiler
10042.00003
4
O-ring
5
Countersunk screw DIN 965 M3x5
10042.00004
10042.00005
6
Retaining ring sealing
10042.00006
7
Sealing for KS sliding flange
8
Cylinder screw DIN 7984 M8x13
10042.00007
9
Cylinder screw DIN 7984 M8x30
10 Disk DIN 125 8.4A
11 Sealing for BS sliding flange
12 Hexagon nut DIN 934 M8
13 Cylinder screw DIN 7984 M8x30
6
14 Disk DIN 125 8.4A
7
5
10023.00187
10014.00129
10044.00026
10044.00027
10002.00114
10023.00002
10002.00141
10006.00108
10023.00043
10004.00328
10006.00003
10023.00063
10023.00008
10023.00020
10006.00007
10023.00002
10023.00008
10023.00020
Publicité
Table des Matières
