Whirlpool W11449282C Instructions D'installation page 14

CODE
F4 Signal Strength Mode allows machine to show current signal
strength of Wi-Fi.
F4 Pressing the DELICATES key while on the F4 screen will toggle
between F4 and the signal strength in dBm.
g
Press the MIXED key once to advance to next code.
F5 Deprovision Mode allows machine to be disconnected from Wi-Fi.
F5 This will be displayed if no action is taken.
F5.dP This will flash on the display for 5 seconds while the machine
disconnects from Wi-Fi. In order to deprovision the machine press
the DELICATES key 3 times.
g
Press the MIXED key once to loop to beginning of this menu.
F3.dS WPS Setup Mode
F3 menu allows user to toggle between WPS or uAP
Wi-Fi connection. In order to toggle between uAP and WPS
connection, press the DELICATES key 3 times while on the
F2.XX screenThe F3 screen also acts as a status screen:
"F3.En" and WPS countdown timer will toggle on the display
■
if WPS provisioning is enabled and machine is currently
searching for the router.
"F3.dS" will be displayed if WPS provisioning is disabled and
■
machine is currently not connected to the router or Whirlpool
server. This will also be displayed if WPS connection not
successful before the WPS timer expired.
"F3.Cr" will be displayed if machine is connected to router but
■
NOT connected with Whirlpool server.
"F3.CS" will be displayed if machine is connected to router
■
AND connected with Whirlpool server.
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS.
2xxx Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the MIXED keypad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number of dollars in HUNDREDS.
4xxx Number of dollars in ONES.
5 xx Number of CENTS.
CONTROLS SET-UP THROUGH USB
To access the USB setup menu, navigate to set-up code 2.xx.
Pressing HEAVY DUTY keypad activates the help mode sub-
menu. The first sub-mode within the help mode is USB option.
Press HEAVY DUTY keypad at any time to exit help mode.
S d
ubmode eScription
USB While on this screen, press the HEAVY
DUTY button to enter into USB menu.
USB menu allows for software update
and import/export machine settings.
14
EXPLANATION
1 02 = 2,000
2225 = 225
TOTAL CYCLES = 2,225
3 01 = $1,000.00
4600 = $ 600.00
5 75 = $ 00.75
TOTAL = $1,600.75
n
ote
Allows user to enter
USB menu. See USB
MENU section for
more information.
USB MENU
While on the USB screen press the HEAVY DUTY key. To
advance through the USB sub menu, use the MIXED key. The
DELICATES key is the Select key. Press the HEAVY DUTY keypad
at any time to exit USB Menu.
See Page 15 for location of the USB Port on the appliance and
instructions for how to install a USB Stick onto the appliance and
to remove a USB stick from the appliance.
CODE
U0.00 USB drive Inserted? (Status only).
U0.00 This will be displayed if USB drive is NOT detected.
U0.01 This will be displayed if USB drive is detected.
g
Press the MIXED key once to advance to next code.
U1.00 Programming Mode
U1.00 This will be displayed if USB drive not detected.
U1.01 This will be displayed if USB drive is detected. If you wish to
reprogram the controls Press the DELICATES key 3 times.
Display will toggle between U1.01 and ProG while programming
in process. Please wait until process is complete, this could take
several minutes. After software is successfully downloaded to
machine, the control could take several minutes to reset. After
reset is complete the machine will return to customer mode or
service mode depending on Service Switch status.
Err If the software programming was unsuccessful the display
will toggle between U1.00 and Err.
g
Press the MIXED key once to advance to next code.
U2.00 Export Machine Settings to USB Drive.
U2.00 This will be displayed if USB drive is not detected.
U2.01 This will be displayed if USB drive is detected. If you wish to export
machine settings to USB drive press the DELICATES key 3 times.
Display will toggle between U2.01 and --.-- while export in process.
donE Display will toggle between U2 and donE when export
finished successfully.
Err If the export was unsuccessful the display will toggle
between U2 and Err.
g
Press the MIXED key once to advance to next code.
U3.00 Import Machine Settings from USB Drive.
U3.00 Import Machine Settings from USB Drive.
U3.01 This will be displayed if USB drive is detected. If you wish
to import machine settings from USB drive to machine
press the DELICATES key 3 times. Display will toggle
between U3.01 and --.-- while import in process.
donE Display will toggle between U3 and donE when import
finished successfully.
Err If the import was unsuccessful the display will toggle
between U3 and Err.
g
Press the MIXED key once to loop to beginning of this menu.
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
COIN Models: Reinstall access door.
■
NON-COIN Models:
■
g
Unplug washer or disconnect power.
g
Open console, reinsert plug into J4, close console.
g
Plug in washer or reconnect power.
I
f preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
EXPLANATION