KIKKA BOO Sky high Mode D'emploi page 6

WARNINGS
• Please read this manual carefully before using, please properly kept for future reference, and if the transfer of product delivery please send instructions.
• If not according to the manual operation, may affect the safety of the baby.
• Baby when using chairs, guardians shall not be allowed to leave.
• This product is suitable for age 6 -36 months.
• Such as eat chair anywhere there is broken, torn or missing, please do not use.
• Ensure that all users are familiar with the product operation method, ensure that the product can easily open and close, if not please do not forcibly operation, please read
the instructions carefully, and use the right method.
• Use of highchair, please read all parts installation and fine adjust right, make sure all the lock position is locked.
• Children ride, seat belts must be used to prevent the baby fall or slip out from the high chair, causing serious damage.
• When your baby can't sit up their own, please do not use this product.When your baby in the chair, please do not remove any parts of tables and chairs or adjust any other
part of the chair.
• Don't let your baby climbing, playing alone or hanging on the chair.This product can only be used when on a flat, stable ground. At the same time, please do not place
heavy objects on plates, in case of eat chair turn to.
• Avoid placing chairs near the heat source, such as electric heaters, gas heating lamp, or any place to let the baby contact with dangerous goods.
• Before use, be sure to remove all the plastic bags and packaging materials, in order to prevent the baby in danger of suffocation.
I. PARTS LIST
1. Dinner plate x1; 2. Pedal x1; 3. Seat x1; 4. Non-slip mat x4; 5. Aluminum Tube x4 (Mark NO.1); 6. Aluminum Tube x4 (Mark NO.2); 7. Aluminum Tube x4 (Mark NO.3);
8. Aluminum Tube x4 (Mark NO.4); 9. Aluminum Tube x4 (2 Mark L); 10. Gasket x4; 11. Nut x4; 12. Screw x4; 13. Safe Belt x1;
II. FOOT TUBE INSTALLATION AND FIXATION
Remove products from the packing, please properly handle bags will high chair backrest nd good position stable on the whole.Take out the tube feet, rst install four feet
above the tube (tube at the top of the foot marked with Numbers 1, 2, 3, 4, please insert in order, with your ngers and hold feet on metal dots on the tube, and then aim
at the hole under the chair, directly inserted until metal buckle point and holes overlap. Insert according to the position as shown in gure .
III. Take out the remaining four foot tube, foot tube bottom marked with the letter L for the back foot tube, no mark for the front foot tube, and nd a good place to put the
dining chair. Press the metal point on the foot tube with your nger, then aim at the hole under the foot tube of the highchair and insert directly until the metal point
overlaps the hole as shown in gure .The following four foot tubes are exactly the same in style and mounting.
IV. INSTALLATION AND FIXATION OF BASE
Remove the four footpads of the highchair from the packing case. Place the highchair on the ground, rst press the metal point on the foot tube with your nger, then aim
at the hole of the foot pad, and directly insert until the metal point and hole overlap and buckle.
V. INSTALLATION AND FIXING OF PEDALS
Remove the pedal and screws tool from the package. Install the high chair on the ground, insert the screw into the hole and tighten with a screwdriver, as shown in the
gure.
VI. INSTALLATION AND FIXING OF LEATHER CUSHION
Put the leather cushion on the seat can be.
VII. INSTALLATION OF SEAT BELTS
Press the two tongues of the belt buckle to unfasten it.
VIII. INSTALLATION OF SEAT BELTS
Safety rope through two ways of eat chair .Safety rope wear into the can in two ways, will be subject to the baby comfortable.
IX. INSTALLATION OF SEAT BELTS
Run the belt through the openings of the dining chair. For more convenience, there are two ways to t the belt.
X. INSTALL AND FIX THE TRAY
Place the plate, insert it into the corresponding hole and fold it down. The hole is divided into two gears, which can be adjusted according to the size of the baby's body
shape.
XI. MAINTENANCE AND CARE
• The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
• Do not let the product exposed to the harmful e ect of external factors - direct sunlight, rain, snow or wind. This may lead to damage of the metal and plastic parts and
fading of the fabrics of the crib.
• When you are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low room temperatures.
From time to time check all plastic parts that are hanged on the frame. Tighten all screw and bolts if necessary.
• Cleaning the cushion: Unfasten the safety belt. Wash it with warm water and dry it to avoid exposure under high temperature.
• Do not use bleach and strong acid/base liquid for cleaning the chair frame. Avoid contact with water in hardware parts, as corrosion will a ect the service.
ENGLISH