Publicité
Les langues disponibles
Les langues disponibles
English
•
Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may
wear string rapidly.
•
Do not allow spool cap
other surfaces.
•
In long growth, cut from the top down and do not
exceed 13" (330 mm) high.
•
Keep trimmer tilted toward the area being cut; this is the
best cutting area.
•
The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at the operator.
•
Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Cutting Line / Line Feeding
Your trimmer uses .080" (2 mm) diameter, TWIST nylon line.
During use, the tips of the nylon lines will become frayed and
worn. Cutting line will wear faster and require more feeding
if the cutting or edging is done along sidewalks or other
abrasive surfaces or heavier weeds are being cut.
Clearing Jams and Tangled Line (Fig. L)
WARNING:
trimmer before making any assembly, adjustments or
changing accessories. Such preventive safety measures
reduce the risk of starting the appliance accidentally.
From time to time, especially when cutting thick or stalky
weeds, the line feeding hub may become clogged with
sap or other material and the line will become jammed as a
result. To clear the jam, follow the steps listed below.
CAUTION:
the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade.
1. Remove battery from appliance.
2. Press the release tabs
remove the spool cap from the spool housing
3. Pull the nylon line spool out and clear any broken line or
cutting debris from the spool area.
4. Fit the spool onto the appliance as described in
Replacing Spool Assembly.
Replacing Spool Assembly (Fig. L, M)
WARNING:
not recommended by CRAFTSMAN for use with this
appliance could be hazardous.
WARNING:
or any accessory or attachment other than those
recommended by CRAFTSMAN on this trimmer/edger.
Serious injury or product damage may result.
Reload nylon line (either bulk or prewound replacement
spool) as shown in this manual.
12
24
to drag on ground or
Remove the battery from the
To avoid appliance damage, if
25
on the spool cap
24
10
The use of any accessory
Do not use any blades,
USE ONLY .080" (2 mm) DIAMETER TWISTED NYLON
MONOFILAMENT LINE. Do not use serrated or heavier gauge
line, as they will overload the motor and cause overheating.
This line is available at your local dealer or authorized
service center.
1. Remove battery from appliance.
2. Press the release tabs
remove the spool cap from the spool housing
3. For best results, replace spool with CRAFTSMAN Model
# CMZST080.
4. If lever in base of housing becomes dislodged, replace in
correct position before inserting new spool into housing.
5. Remove any dirt and grass from the spool cap and
spool housing.
6. Unfasten the end of the cutting line and guide the line
into the eyelet.
7. Take the new spool and push it onto the boss
housing. Rotate the spool slightly until it is seated.
8. The line should protrude approximately 5‑3/8" (136 mm)
from the housing.
9. Align the release tabs on the spool cap with the slots in
the spool housing.
10. Snap the spool cap back on by depressing release tabs
and pressing into spool housing.
11. Push the cap onto the housing until it snaps securely
into place.
nOTE: Make sure that cover is fully positioned, listen for
two audible clicks to ensure both release tabs are correctly
located. Power the appliance on. In a few seconds or less
you'll hear the nylon line being cut automatically to the
proper length.
nOTE: Other replacement parts (guards, spool caps, etc.) are
available through authorized service centers. To find your
local service location call: 1‑888‑331‑4569 or visit
www.craftsman.com.
Rewinding Spool from Bulk Line (Fig. M, N)
, and
.
Use Only .080" (2 mm) TWISTED
Diameter Line
Bulk line is also available for purchase from your local retailer.
nOTE: Hand wound spools from bulk line are likely to
become tangled more frequently than CRAFTSMAN factory
wound spools. For best results, factory wound spools
are recommended.
1. Remove battery from appliance.
2. Remove the empty spool from the appliance as
described in Replacing Spool Assembly.
3. Remove any remaining cutting line from the spool.
4. Make a fold at the end of the cutting line at about 3/4"
(19 mm)
anchoring slots
5. Insert the 3/4" (19 mm) end of the bulk line into the
hole
29
line is pulled tight against the spool.
25
on the spool cap
27
. Feed the cutting line into one of the line
28
.
in the spool adjacent to the slot. Make sure the
24
, and
10
.
26
in the
Publicité
