Trotec TTK 650 S-EH Mode D'emploi page 10

Important information regarding the electrical connection
• The unit may only be connected to electrical feed points with a residual
current circuit breaker in compliance with DIN VDE 0100, Part 704.
• It must be ensured that the unit is safe when used in wet areas like utility
rooms, bathrooms or similar rooms by means of a suitable residual
current circuit breaker in compliance with existing regulations.
• Check the information provided on the identification plate of the unit and
make sure that the voltage and the current rating of the energy supply that
you wish to connect the unit to fulfil the necessary requirements before
you connect the unit to the power supply.
• If a generator is used to produce electricity, then it must have an output
of at least 5 kW because the unit's starting current can exceed its
nominal current by as much as four or five times.
06. Operation
The mains supply switch and the humidistat control on the right-hand side of
the unit are the key control elements which enable you to operate the unit. See
figure C for a visual representation of the relevant operating controls.
07. Starting Up
Before starting up, please check the air intake and air outlet ducts for obstruc-
tions and check the air filter to ensure that it is not blocked or clogged. Blocked
or clogged filters or grilles must be cleaned immediately. See chapter 10 "Clean-
ing and Maintenance" for further instructions.
Important information before starting up
• Cable extensions must have the required cross-section.
• Cable extensions must be completely unrolled.
Starting Up the Unit
1. These safety instructions must be observed at all times.
2. Connect the mains plug of the unit to a correctly fused socket
(230 V / 50 Hz / 16 A).
3. Installing a condensate discharge system.
Because the TTK 650 S-EH has such a high dehumidification performance, the
unit is not equipped with an internal condensate tank. Please ensure that one of
the four following alternatives is provided so that the condensate can be either
be collected in an external tank or conducted away from the unit.
3.1. Collecting the condensate in an external tank
Place a suitably-sized tank (>100 litres) below the water discharge point at the
bottom of the unit (see fig. C.9). Connect one end of the water discharge hose
included in the scope of delivery (see fig. C.10) to the water discharge point at
the bottom of the unit and hang the other end of the hose over the tank or place
it in the tank so that the water can drain off from the unit without causing any
damage to the location where the unit has been installed.
Please make sure that the water level in the tank is checked regularly and that
the tank is emptied before the water that has been collected runs over. The
tank will have to be checked and emptied more often when humidity levels in
the room are higher and the dehumidification performance is greater.
3.2. Conducting the condensate into a drain
Connect one end of the water discharge hose included in the scope of delivery
to the water discharge point at the bottom of the unit and connect the other end
of the hose to a drain so that the water can drain off from the unit without
causing any damage to the location where the unit has been installed.
B 3
Please make sure that the water discharge hose slopes downwards all the way
to the drain so that the water can drain off properly. You may wish to connect
another hose of the same type depending on the distance to the drain.
3.3. Using an automatic condensate pump to dispose of the condensate
There is an automatic condensate pump available as an optional accessory.
The pump is suitable for use during non-stop operation. When you use a con-
densate pump, please make sure that you follow the separate instructions that
come with the pump.
4. Press the mains switch to mode "I" (see fig. C.3).
5. To start dehumidifying set the relative humidity value
to the setting you wish to select as described in the chapter
"Selecting the desired relative humidity value".
The unit is now in operation and will now run according to the setting you have
selected. To turn off the unit press the mains switch to mode "0".
Important information regarding operating the unit
• The unit will not start up again automatically when the power returns
after the power supply has been previously cut or interrupted.
• The fan runs the whole time from the moment the unit is switched on
until it is switched off again. This is so that the built-in sensor can
measure the relative humidity in the room accurately and reliably.
What to watch out for when using the unit
for the first time and information on how to operate
the electronic humidistat controls
The dehumidifier is equipped with electronic humidistat controls with a preselection
mode that allows you to set the relative humidity to the value you wish to select
as a percentage value. To achieve the highest possible dehumidification perform-
ance set the percentage value to 40 %. To achieve the lowest possible dehumidifi-
cation performance (ie. no dehumidification) set the percentage value to 90%.
The digital display shows the existing relative humidity (see fig. C.5).
It may take a short while for the humidistat to determine the existing relative
humidity and present it on the digital display when you are using your unit
for the first time.
Selecting the desired relative humidity value
Press the SET key (fig. C.7.) to select your individual relative humidity value.
The digital display now switches from the existing relative humidity value to the
value you have selected.
Press the setting keys (fig. C.6) to increase or lower the value on the display
until you have reached the value you wish to select. Press the upper setting key
to increase the value and the lower setting key to reduce the value. Either press
the SET key again to confirm the value or wait approximately 30 seconds. The
value you have selected is now stored and the digital display will once again
show the existing relative humidity value.
Important: Because of the way the unit is designed it is possible to select
a value between 0 and 100 %. If you do, however, select a value that is
<40 or >90 %, then the dehumidifier will not be able to operate at this set-
ting as these values are not within the dehumidifier's performance range.
Please be sure to select a value between 40 and 90 %!
The humidistat determines the existing relative humidity via the air inlet (fig.
C.8). Please ensure that a distance of at least 50 cm is kept to any objects or
walls so as to allow convection to occur and for the air to circulate freely.
Set the selection value of your dehumidifier to the highest possible value, ie.
40 % when using the dehumidifier for the first time.
Allow your dehumidifier to run with this selected value. Initially, the dehumidifier
will extract large amounts of moisture from the air and will continue to do so
until there is less moisture in the air.
Operating Instructions Dehumidifier TTK 650 S-EH
EN