Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EN
7 DAY AND DAILY PROGRAMME
INTEGRATED, ENERGY SAVINGS
AUTOMATIC PROGRAMMING WITH SELF-LEARNING
PROCESS
This feature is available on products equipped with occupancy detector.
Overview
Auto-programming (Auto): After an initial learning period of one week,
the device will analyze occupancy cycles to determine and implement
a weekly programme adapted to your lifecycle alternating comfort pe-
riods (automatic boost period launching) and periods in eco, the goal
being to deliver the most efficient yet comfortable and user focused
heating cycle. Each start of comfort period launches a boost period. The
duration of this boost is the one set on manual boost
page
4.
The products algorithm will perpetually learn and adapt to changes in
your occupancy patterns, adapting week after week to optimize the hea-
ting programme to any changes in your evolving occupancy patterns.
Operating
Upon the first activation of your de-
vice, the mode "auto-programme" is
activated by default,
in mode Auto. To deactivate and
change the programme,
see choice
and affectation of programmes page
8.
The first week of operation is a lear-
ning week during which the device
memorizes your habits and elabo-
rates a program for the week.
It therefore defines a programme
built up of Comfort and Eco, inde-
pendently for each day of the week.
During this learning week, the device
will provisionally function in permanent "Comfort" mode, means only
manual boost are possible.
Important:
To ensure the auto-programming is optimized, please en-
sure the presence detection sensor is not interrupted by an external
source,
see important information concerning the presence detection
system on page
10.
Application of the intelligent program
One week after switching on, the device will apply the new program for
the next 7 days. Then week after week the device will continue to opti-
mize the intelligent program "Auto", adjusting the Boost launch and Eco
periods to fit closely to your lifestyle.
When the product is in Frost protection mode or in standby mode for
more than 24 hours, learning and optimization of the intelligent pro-
gram stops: the device stores the previously recorded program from the
last week before switching to the Frost protection or standby mode.
- Example 1: If the product is installed in mid-season or if its installa-
tion is anticipated on the construction site, it can be switched on in
standby mode. When you select the Auto mode, the learning week
will start automatically. The device will be in permanent comfort and
will memorize your habits to apply the adapted program the following
week.
- Example 2: You select frost protection mode before going on holiday.
Upon your return, when you return to Auto mode, the unit will auto-
matically apply the previously stored intelligent program from the last
week before you left.
M16MI325 A03_06/18
7 DAY AND DAILY PROGRAMME
In this mode, you have the option of programming your device, by
setting one of the five programmes on offer for each day of the week.
Each transition Eco to Comfort, a Boost will be launched for the duration
set on manual Boost
Access to the programming mode
From Auto, Comfort, Eco or Frost protection mode, press
seconds to enter into the programming mode.
Schematic sequence of programming settings:
Setting day and time
see Boost feature
In this mode, you can set day and time to program your device in line
with your needs.
1- From Auto, Comfort, Eco or Frost protection mode, press
seconds.
The cursor moves to the setting day and time mode.
3
Example of display
in Comfort period
2- Select using
The hours will scroll quickly, if you press the
them.
Save by pressing
3
Example of display
in Eco period
3- The two minute figures will flash.
Select using
Save by pressing
see Boost feature page
Setting time
Setting day
1
5 sec.
or
. The two hour figures will flash.
.
1
1
or
.
.
1
1
5.
for 5
Programmes
choice
for 5
or
and hold
2
2
6
Publicité
Chapitres
Table des Matières
